Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0416
Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output
Reference: RBD-1424
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-1326
Outer Diameter: 68 mm. Supply Voltage: DC 4-7V. LED driver chip: WS2812B Communication interface: single wire communication. Send data at speeds of 800Kbps. The color of the light was highly consistent Full-color module, Full-color soft lights a lamp strip
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0889
Rugged chrome-plated metal pushbutton with blue LED ring Ideal for panels up to 1/2" thick Easy installation with a simple drill hole Built-in resistor for LED Supports 3 to 6V for LED operation Momentary pushbutton design
Reference: RBD-0890
Rugged chrome-plated metal pushbutton with red LED ring Latching design for maintaining the switch state Built-in resistor for LED Supports 3 to 6V for LED operation IP65 and IK08 protection ratings Durable stainless steel and chrome-plated brass construction
Reference: RBD-0891
Rugged chrome-plated metal pushbutton with red LED ring Latching design for maintaining the switch state Built-in resistor for LED Supports 3 to 6V for LED operation IP65 and IK08 protection ratings Durable stainless steel and chrome-plated brass construction
Reference: RBD-0892
Rugged chrome-plated metal pushbutton with red LED ring Latching design for maintaining the switch state Built-in resistor for LED Supports 3 to 6V for LED operation IP65 and IK08 protection ratings Durable stainless steel and chrome-plated brass construction
Reference: RBD-1098
Interface: I2C Operating Voltage: 3-5VDC Ports: 8-bit Parallel Ports Can be used with Arduino and Raspberry Pi
Reference: RBD-2638
Doublepow 14500 3.7V 850mAh Battery High-capacity lithium-ion cell Fast charging with small internal resistance Suitable for flashlights, toy cars, power banks, and more Compact size and lightweight design High capacity (805mAh) for extended runtime in compatible devices. Compact 14500 cylindrical design (14mm x 50mm). 3.7V nominal voltage - replaces...