Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-2065
Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: RBD-1753
Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-2303
LED peak wavelength: 660nm/880nm LED power supply voltage: 3.3~5V Detection signal type: light reflection signal (PPG) Output signal interface: I2C interface
Reference: RBD-2309
Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! This module contains an ESP8285, which is an ESP8266 processor with 1MB of FLASH memory already built in. You can use it just like an ESP8266, it's the same processor and WiFi The ESP8266 processor from Espressif is an 80 MHz microcontroller with a...
Reference: RBD-2307
This speaker is a great addition to any audio project where you need 8 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm...
Reference: RBD-2853
Shape: Circular. Sensing Area diameter 5mm Min Force: 20 gm. Max Force: 1Kg. Length (mm): 65. Weight (gm): 2.
Reference: RBD-1328
Size: 0.96 inch Resolution: 128 x 64 Controlling Chip: SSH1106 Display Area: 21.74 x 10.86mm Driving Voltage: 3.3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-2449
Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink