Reference: RBD-0354

TSL2561 Luminosity & Infrared Light integrating sensor

Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD

Reference: RBD-0624

FM Radio Transmitter Module Wireless Microphone Surveillance Frequency 88-108MHz

Operating Voltage: DC 2V- 9V  Operating frequency: 85MHZ - 115MHZ Output Impedance: 50 ohms

Reference: RBD-1101

5V Micro USB Tiny AVR ISP USBTinyISP Programmer Module For Arduino IDE Bootloader ISP Microcontroller

1 review

Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

1 review

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-1854

Resistive Film Pressure Sensor Module Pin Header Analog Signal 200mm

This module is compatible with various microcontroller control boards, such as arduino series microcontrollers. The module contains 2 kinds of interfaces. The module comes with a 20cm wire, which is long enough for your use. It has a short response time and quick response.

Reference: RBD-1670

ESP8285 IR Infrared Transmitter Receiver Module WIFI Remote Control Switch

The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA

Reference: RBD-0349

Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board

31 reviews

Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...

Reference: RBD-1809

Digispark Pro - ATtiny167 with Micro USB

Digispark Pro  ATtiny167  Micro USB 16MHz

Reference: RBD-2248

TE Connectivity LDT0-028K Piezoelectric Sensor Vibration Silver Ink Electrode No Mass Version

1 review

Model: LDT0-028K Solder tab connection Withstands high impact

Reference: RBD-1203

Sharp GP2Y0A21YK0F Analog Distance Sensor 10-80cm

4 reviews

Distance measuring range: 10 cm to 80 cm Output type: Analog voltage Output voltage differential over distance range: 2.05 V (typical) Update period: 38 ± 10 ms

Reference: RBD-1215

ATmega328P-PU PDIP-28 Microcontroller

9 reviews

131 powerful instructions – Most Single Clock Cycle Execution 32 x 8 general purpose working registers Fully static operation Up to 20MIPS throughput at 20MHz On-chip 2-cycle multiplier Write/erase cycles: 10,000 flash/100,000 EEPROM Optional boot code section with independent lock bits In system programming by on-chip boot program True read while write...

Reference: RBD-1750

Instrumentation Voltage Amplifier Module AD620

2 reviews

Operating Voltage: 3- 12 VDC Amplification: Adjustable 1.5~1000 times Signal Input Voltage Range: 100µV~300mV Signal Output Range: 100µV~300mV

Reference: RBD-2819

GPS Embedded Antenna - SMA Male

Superior Signal Strength: Powerful 26dB gain LNA antenna for exceptional GPS reception. Compact Design: Ideal for integrating GPS functionality into space-constrained projects. Easy Integration: Unpackaged design with SMA connector simplifies setup. Durable Construction: Built to withstand moderate vibrations.

Reference: RBD-0937

Mini Data Logger Module

2 reviews

SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...