Reference: RBD-1330

AC Light Dimmer Module, 1 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A

Reference: RBD-1880

12V 500RPM 25GA Gear Motor

Voltage: 12V DC RPM:500RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions

Reference: RBD-0439

Arduino Android IOS HM-10 BLE Bluetooth 4.0 CC2540 CC2541 Serial Wireless Module

Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....

Reference: RBD-0565

5 axis CNC Breakout Board with optical coupler For Stepper Motor Driver MACH3

Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software. USB power supply and peripherals power phase are separate to protect computer security. All the signals are to-isolate which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc. Wide input voltage range: 12-24V, and with...

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-2251

BALA-C PLUS ESP32 Self-Balancing Robot Kit

ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38

Reference: RBD-1162

15G Solid Rosin Welding Soldering Flux Paste High Purity

Net Content: 15g Paste Color: Brown Does not create High Smoke Does not create Foul/Bad Smell No Residual Waste High-Quality Soldering Additives & Activators for effective soldering Useful for general purpose soldering, electrical wires, components, and cables etc

Reference: RBD-0289

16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685

Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED

Reference: RBD-0623

DC-DC 9V/12V/24V to 5V USB Step Down Power Module 2A

Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD

Reference: RBD-0653

Male Pin Header Single Row (L Shaped)

Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)

Reference: RBD-0180

Brand: SparkFun Electronics

Makey Makey Kit

Description: This is the same product as the Makey Makey Standard Kit. The difference is this version comes in fancy clamshell packaging meant for our distributors that need it. Regular customers are welcome to order, but we want to limit the amount of extra packaging finding its way into the trash heap.

Reference: RBD-0741

433MHz 100 Meters ASK Wireless Module Kit RF

Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards

Reference: RBD-0274

Brand: Waveshare

Raspberry Pi 5inch Resistive Touch HDMI LCD

5 inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi Installation Instruction: http://www.waveshare.com/wiki/5inch_HDMI_LCD Raspbian Image for 5 inch HDMI Diplay with Touch :  Raspbian 5 inch HDMI with Touch Download Link    

Reference: RBD-2002

Short U Servo Bracket

U Bracket 2mm Hard aluminum  Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...

Reference: RBD-0415

801S Vibration Sensor Module

Has a signal output instruction When the output valid signal is high, the light goes out The sensitivity is adjustable (fine-tuning) The wide detection range of vibration, no direction With mounting holes, firmware installation is flexible and convenient. RoboticsBD

Reference: RBD-0041

Smart Speed Detecting Sensor for Arduino

Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.

Reference: RBD-0440

HC-12 433Mhz Wireless Serial Transceiver Module - 1 Kilometer

433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD

Reference: RBD-0573

DC 5V Stepper Motor with ULN2003 Driver Board 28BYJ-48

Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm

Reference: RBD-0161

20x4 Character LCD

Model: LCD2004 Character Color: White Backlight: Blue Supply voltage: 5V Dimensions(L x W x H) mm: 98 x 60 x 12

Reference: RBD-1960

Mini Peristaltic Pump Head with Tube

Small size, light weight. Embedded in the work front panel Mounted on the carriage.

Reference: RBD-1565

Robotic Arm Edge Kit

MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm

Reference: RBD-0691

IR Infrared Remote Decoder Encoding Transmitter & Receiver Wireless Module

Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters 

Reference: RBD-0315

US-015 Ultrasonic Module Distance Measuring Transducer Sensor

Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm. RoboticsBD

Reference: RBD-1573

Five-Way Navigation Button Module 5D Joystick Independent Keyboard Switch Button Single Chip

Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm

Reference: RBD-1892

14500 Lithium Battery Charger USB Micro-B

Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.

Reference: RBD-0699

1.8" inch TFT LCD Display module ST7735S 128x160

Display Size: 1.8″ Driver IC: ST7735 Input Voltage (V): 3.3 to 5 Pixel Resolution: 128 x 160 Interface Type: SPI

Reference: RBD-2105

Male to Male Jumper Wires 40 Pin 30cm

40P color jumper wires Length: 300mm Weight: 45 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-1843

10.5 inch Jumper Wire

The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-2541

Brand: DFRobot

Gravity: Voice Recorder Module

This is the latest voice recorder module with integrated record and play functions. Easily record your voice by pressing the record button, speaking and then releasing the button when finished. The module is able to playback 10 seconds in total. Connect an 8Ω 3W speaker or an external active speaker for voice output. The module also has a 3 pin digital...

Reference: RBD-0922

Slide Potentiometer 10K Linear Module Dual Output for Arduino

Dimensions: 91 x 21 x 30 mm(LxWxH) Weight: 18 gm. Voltage: 3.3V or 5V. Port: Analog. Resistance: 10K. Appn: Raspberry-Pi projects. DIY projects., Arduino projects.