ESP8266 ESP-01 WIFI Wireless Transceiver Send Receive LWIP AP+STA M70

US-015 Ultrasonic Module Distance Measuring Transducer Sensor

  Features: Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm

APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW

Description: This Telemetry radio set allows you to link to  a flight controller such as the APM or Multiwii  AIO via a USB equipped device such as a  computer, laptop or tablet supporting a USB  connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)

Tolsen Cordless Screwdriver (Set)

Cordless Screwdriver With Set

Brand: DFRobot

Arduino GPS/GPRS/GSM Shield V3.0

INTRODUCTION This is a Arduino GPS/GPRS/GSM shield from DFRobot. This shield with a Quad-band GSM/GPRS engine works on frequencies EGSM 900MHz/DCS 1800MHz and GSM850 MHz/PCS 1900MHz. It also supports GPS

3D Printer Controller for RAMPS 1.4 REPRAP MENDEL PRUSA

Specification: Fully assembled & tested, no soldering required. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. 3D Printer Controller for RAMPS 1.4

Weighing Sensor 24 Bit HX711 Dual-Channel

Weighing Sensor 24 Bit HX711 Dual-Channel Precision A/D Module Pressure Sensor. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. 

TSL2561 Luminosity & Infrared Light integrating sensor

TSL2561 Luminosity & Infrared Light integrating sensor

Motor Driver 43A BTS7960

I2C Level Conversion Module 3~5V Fro Arduino

Specification   Level conversion for Arduino Board with 5V-3V regulated power supply module; 2-channel 5-3V dual-directional communication interface, IIC / I2C level conversion module, 3~5V system

Brand: SparkFun Electronics

Graphic LCD 128x64 STN LED Backlight

Description: This is a framed graphical LCD 64x128 with  LED backlight. This unit is a very clear STN type LCD with  a simple command interface. This new module includes the negative voltage circuitry on board!

9 Degrees of Freedom Breakout- MPU9150

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Multifunctional Standard Aluminium Servo Bracket

Aluminum Pan and Tilt for a horizontal surface, unassembled; Pan and Tilt Mount Servo Stand for Robot Clamp Claw; Servo bracket used in the shoulders and knees or other joints of humanoid robots, biped robots etc. Comatible With: MG996R, MG995  

Digital PH Meter Tester Aquarium Pool Water Urine Wine LCD Pen Monitor Protable

This digital pen style PH meter is an ideal instrument for any aquarium, the fishing industry, swimming pools, school laboratories, food, beverage etc.This PH meter is highly efficient and accurate due to its advanced microprocessor technology.Big LCD display screen which has great waterproof performance and let you easily read the displayed value....

4-20MA -50~150℃ RTD PT100 SBW Temperature Sensor Transmitter Module

Metal Servo Horn

Disk type metal servo horn for MG945, MG996, MG995 and MG946 servos.

Torobot 32 Channel USB UART Servo Motor Controller

32 Channel USB UART Servo Motor Controller  Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.

Dupu Nano Li-po Battery 2200mAh 11V 3S 20C

Specification: - Weight: 176g- Size: 21*32*107mm- Single rated voltage: 3.7V- Single full charged voltage: 4.2V- Battery pack rated voltage: 11.1V- Battery full charged voltage: 12.6V- Continuous discharge rate: 20C- Battery pack rated capacity: 2200mAH- Cell material: Nano li-polymer

Brand: RoboticsBD

Abs Material Pan Tilt Camera Mount With Servo Motor

3D Printed Pan Tilt Camera Mount With Servo Motor   Package Include: 1x 3D Printed Pan Tilt Bracket 2x 9g Servo Motor (Assambled with the Pan Tilt Bracket)   Fully assembled 3D Printed (ABS Filament) strong Pan Tilt Camera Mount With Servo Motor 9g

Battery 9V

Battery 9V

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Monster Moto Shield uses VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! Voltage max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Thermal Shutdown

UART EM4100 RFID Card Reader RDM6300

Overview RDM6300 125KHz cardreader mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.

Brand: DFRobot

APC220 Radio Communication Module

INTRODUCTION The APC220 radio module provides a  simple and economic solution to wireless data communications. Integrates an  embedded high speed microprocessor  and high performance IC that creates a  transparent UART/TTL interface, and  elminates any

ADS1115 16 Bit I2C 4 channel ADC Module

5mW Adjustable Laser Dot Diode Module

5mW Adjustable Laser Dot Diode Module Features: 1. Output Power: 2-5mW2. Wavelength: 650nm3. Working Voltage: 3v - 5v4 .Laser Shape: Dot5. Working temperature: -10 C-40 C

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

85mm Antiskid Shockproof Wheels, Smart Car Robot Tires

85mm Antiskid Shockproof Wheels, Smart Car Robot With Wheel Coupling + Motor Mounting Bracket 

AMG8833 IR Thermal Camera Breakout (Adafruit Compatible)

Add heat-vision to your project and with an AMG8833 Grid-EYE Breakout! This sensor from Panasonic is an 8x8 array of IR thermal sensors. When connected to your microcontroller (or raspberry Pi) it will return an array of 64 individual infrared temperature readings over I2C. It's like those fancy thermal cameras, but compact and simple enough for easy...

Waterproof DS18B20 Digital Thermal Probe or Sensor

This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!

Arduino Bluetooth Module (HC-05)

Arduino Bluetooth Module (HC-05) This serial Bluetooth module can work as either master or slave. This module also includes the baseboard, not only the core board, most functions are pre-set, so only the serial port communication is available but it’s easier to use. It can be used also with Arduino or Microcontroller.

65mm Rubber Wheel with 25GA Motor Mounting Bracket

1 x 65mm Wheel 1 x Mounting Bracket for 25GA Motor 1 x Hex Coupler for 25GA Motor 1 Set of Installation Screws