- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- Power Module & Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- Retired Products
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Male Pin Header Single Row
Male Pin Header Single Row (40 Pin set)
Store Pickup Available!
Free Ship Over 5000 BDT
INTRODUCTION The APC220 radio module provides a simple and economic solution to wireless data communications. Integrates an embedded high speed microprocessor and high performance IC that creates a transparent UART/TTL interface, and elminates any
01S Vibration Sensor Module vibration Analog Output Sensitivity LM393Size: 41 * 15 * 12.5mm The main chip: LM393, vibrating probe Operating voltage: DC 3-5V Main features: Has a signal output instructions; With analog and TTL-level signal output signal; Output valid signal is high, the light goes out; Adjustable sensitivity (fine-tuning); Vibration...
Brand: SparkFun Electronics
Rover 5 Robot Platform 4 Motors 4 Encoders Description: If you’re looking for a base for your next robot, look no further than the Rover 5. The Rover 5 uses 4 independent motors, each with a hall-effect quadrature encoder and gearbox.
Precision Real Time Clock Module DS3231 AT24C32 I2C With Battery
This is a 12V 4-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) . **Relay Brand is different from the picture as per stock
It is a UPS uninterruptible power supply control board. DC 9V Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
5V ESP8266 Dual WiFi Relay Module Internet Of Things Smart Home Mobile APP Remote Switch
Product Name : DC Solenoid Electromagnet;Model : JF-0530B;Rated Voltage : DC 12V RatedCurrent : 300mA;Action Form : Pull Push Type;Rated Stroke & Force : 10mm, 5N Body Size : 30 x 15x 15mm/1.2"x 0.59"x 0.59"(L*W*H);Pluger Dia. : 56mm/ 2.2" Cable Length : 20cm/ 7.9";Material : Metal, Electronic Parts Weight : 32g;Package Content : 1 x DC Solenoid...
USB Host Shield For Arduino UNO, MEGA, Compatible with Google Android ADK
Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S
Brand: SparkFun Electronics
Description: This is a 7" LVDS LCD Cape for the pcDuino V3 with a 1024x600 screen resolution and capacitive touch from LinkSprite. This massive screen is a great addition for the pcDuino V3 that compliments its extreme versatility as a mini PC development platform.
Specifications:- Gain: 2.0dBi-2.5dBi- Standing-wave ratio (SWR): <1.5- Directivity: Omni-directional- Center frequency: 5.8Ghz- Connector: RP-SMA- Diameter of connector: 7.67mm- Length:Transmitter antenna:71mm- Receiver antenna:91mm- Net weight: 12g（Tx/Rx）- Package weight:69 g
Details For plug-in test boards, the 3.3V and 5V power supplies have jumper to adjust the desired power. Supports 9V battery jacks, 6.5 - 12V input power adapter, or power supply.Access via USB via Mini USB cable is small space wasted experiment board.
(Retired) This durable tracked chassis is a complete robot base for your tank-like robot. With a battery holder, two DC motors, and two independent geared drive trains included, this chassis is just a robot controller and some sensors away from a complete robot. This chassis is gray. Additional L298 Motor Drive Board is included with this chassis.
Features: Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm
It looks like a servo, it acts like a servo, but it's more than just a servo! We got a factory to custom-make these classic 'standard' sized hobby servos with a twist - the feedback (potentiometer wiper) line is brought out to a fourth white wire. You can read this wire with an analog input such as those on an Arduino, to get the servo's position.
এই লাইট হোল্ডার টি মানুষের উপস্থিতি পেলে লাইটটিকে অটোমেটিক চালু করে দিবে। Infrared Sensor Automatic Lighting Control Switch with lamp holder; convenient, safe & practical. Good solution for energy saving. You can conveniently let the light auto on/off. The switch can detect the human body's infrared, and use infrared to control the load. Easy...
• Switching capacity available by 10A in spite of small size design for highdensity P.C. board mounting technique. • UL,CUL,TUV recognized. • Selection of plastic material for high temperature and better chemical solution performance. • Sealed types available. • Simple relay magnetic circuit to meet low cost of mass production.
Model 0.8mm Solder Wire Tin Lead Brand Tong Kong Weight 60g Approximate