Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBD-0555

Current Sensor ACS712-30A

5 reviews

Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A

Reference: RBD-0419

SparkFun Particle Sensor Breakout - MAX30105

Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...

Reference: RBD-0559

Voltage to Current Transmitter Signal Module

2 reviews

Power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA  0-5V to 4-20mA Linear Conversion

Reference: RBD-0441

Optical Dust Sensor - GP2Y1010AU0F

9 reviews

Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust RoboticsBD

Reference: RBD-0562

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator

3 reviews

Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm

Reference: RBD-0564

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-0812

High Accuracy I2C MAX30105 Particle Optical Sensor Photodetectors Oximeter Module

1 review

Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.

Reference: RBD-0813

Liquid Suspended Particles Turbidity Sensor Detection Module Kit

3 reviews

Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.

Reference: RBD-1173

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000 100A

3 reviews

Input Current : 100A Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Meet UL94-V0 flame retardant properties

Reference: RBD-0958

Air Quality Breakout - CCS811

4 reviews

Five Operating Modes Integrated MCU Onboard Processing Standard I2C Digital Interface Optimized Low-Power Modes Optional NTC Thermistor Pins

Reference: RBD-1175

Current Sensor ACS712-20A

3 reviews

Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 20A Sensitivity: 100mV/A

Reference: RBD-1042

Capacitive Soil Moisture Sensor

6 reviews

Operating Voltage: 3.3 ~ 5.5 VDC. Operating Current: 5mA. Interface: PH2.54-3P. Dimensions mm(LxWxH): 98 x 23 x 4. Supports 3-Pin Gravity Sensor interface Analog output. Weight (gm): 15.

Reference: RBD-1174

Current Sensor ACS712-5A

8 reviews

Low-noise analog signal path. Device bandwidth is set via the new FILTER pin. 5 µs output rise time in response to step input current. Small footprint, low-profile SOIC8 package. 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.

Reference: RBD-1177

4-20mA Signal Generator Current Loop Simulator Tester

This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...

Reference: RBD-1716

PM2.5 Air Quality Sensor PMS5003 High Precision Digital Output Module

1 review

Working Voltage: 5.0V Maximum Working Current: 100mA Data Interface Level: L＜0.8V, H>2.7V, maximum voltage level 3.3V Particle Measurement Range: 0.3 ~ 1.0μm; 1.0 ~ 2.5μm; 2.5 ~ 10μm Note: Please purchase this adapter board to use it with Arduino and Raspberry Pi. 

Reference: RBD-1344

Current to Voltage Transmitter Module

Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V

Reference: RBD-1719

Envitec OOM202 Medical Ventilator Oxygen Sensor

Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December

Reference: RBD-1424

ZMCT103C 5A Range Single Phase AC Micro Current Transformer Sensor

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-2289

Dust Sensor DSM501A Air Quality Monitoring

Low cost, compact size dust sensor module Used to quantitative particle (> 1 micron) measurement Principle of particle counter Can sense the tobacco smoke and pollen, house dust Consist of light emitting diode lamp, detector, signal amplifier circuit and heater Used in applications such as the air cleaner or air purifier Users can use this sensor...

Reference: RBD-1675

PZEM-004T V3.0 AC Digital Multifunction Meter Watt Power Volt Amp With Coil 100A

1 review

Model: PZEM-004T Operating Voltage: 80-260VAC Test Voltage: 80-260VAC Rated Current: 100A Rated power: 100A / 22000W Operating frequency: 45-65Hz Measurement accuracy: 1.0

Reference: RBD-1751

MP-135 MP503 Air Quality Sensor Module

1 review

Detection Gas: H2, Alcohol, CO, VOC  Detection Range: 10～500ppmH2 5～500ppm Alcohol 10～500ppm CO Air Quality Sensor Module

Reference: RBD-1654

5 In 1 Portable CO2 Detector Air Quality Detector Intelligent Air Detector

3 reviews

5 In 1 Portable  CO2 Detector Air Quality Detector Intelligent Air Detector Temperature and Humidity Sensor Carbon Dioxide Monitor TVOC Formaldehyde Detection HCHO Detector  Color Black

Reference: RBD-1835

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-050 50A

1 review

Input current (RMS): 50A. Work temperature: -25℃～+70℃. Storage temperature: -30℃～+90℃. Work voltage: 660V. Frequency range: 50Hz-1KHz.

Reference: RBD-1836

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000 30A

2 reviews

Input Current : 0-30A Output Mode: 0-1V @ 30mA Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection Meet UL94-V0 flame retardant properties

Reference: RBD-2330

AS7343 Visible Spectrum Infrared Color Spectrometer Sensor

The AS7343 is a 14-channel highly versatile, multi-purpose spectral sensor enabling new consumer, commercial, industrial and laboratory applications. It is optimized for reflective, transmissive and emissive measurements including color matching, fluid or reagent analysis or general spectral reconstruction. The spectral response is defined by individual...

Reference: RBD-1972

Brand: DFRobot

Gravity: Analog AC Current Sensor (20A)

Brand Gravity Analog AC Current Sensor 20A AC Current Signal Conversion Module Open Type AC Transformer Probe Included Non-contact Measurement

Reference: RBD-2508

ENS160 AHT21 Carbon Dioxide CO2 eCO2 TVOC Air Quality Temperature & Humidity Sensor

The ENS160 is a digital multi-gas sensor specifically designed for indoor air quality testing that optimizes the detection of a wide variety of gases and volatile organic compounds (VOCS), including toluene, hydrogen, ethanol, N02 and ozone. The air quality sensor is used in home and building automation, consumer products, electrical and air purification

Reference: RBD-2071

SS49E Linear Hall Effect Sensor Module

1 review

Type: Magnetic Sensor Module Mainly Compatible with: Ardunio

Reference: RBD-2560

Open Smart PM2.5 Optical Powder Smoke Detector Module With Adapter For Arduino

Introducing the Dust Sensor - an optical sensing system designed for detecting airborne dust particles using an infrared emitting diode (IRED) and a phototransistor. The diode and phototransistor are diagonally arranged to effectively capture reflected light from dust in the air. Notably, this sensor is highly efficient in detecting very fine particles,...

Reference: RBD-2072

Linear Magnetic Hall sensor

1 review

Operating Voltage: 3.3V-5V Features wide range voltage comparator LM393 Adjustable sensitivity Signal output indicator with the retaining bolt hole, convenient installation Output form digital switch output (0 and 1 high and low level) The output effective signal is low level When there is sound, outputs low level and the signal light

Reference: RBD-2729

SGP41 Air Quality Digital TVOC Detection Sensor

The SGP41 from Sensirion is an innovative VOC and NOx sensor engineered to serve as a digital smart switch and regulation unit in air treatment systems like air purifiers. Utilizing Sensirion's advanced Gas Index Algorithm, the sensor accurately processes two distinct signals, enabling automatic triggering of air treatment devices for the removal of...