Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1700
Brand: Waveshare
Mini ST-LINK/V2 Small single board Extreme low cost solution In-circuit debugger/programmer STM8 STM32.
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-0719
Bandwidth (KHz): 500. RF Range (GHz): 2.40 ~ 2.48. No. of channels: 6. Remote controller weight (gm): 400. Power: 6V (1.5V AA*4). Antenna Length: 26mm * 2 (dual antenna). Transmitting Power: ≤ 20dBm. RF Receiver Sensitivity: -105dbm. RoboticsBD
Reference: RBD-1830
FT245+CPLD High-Speed Program Altera USB Blaster Download Cable FPGA / CPLD Downloader
Reference: RBD-0103
This is M177 NRF24L01 2.4GHz Antenna Wireless Transceiver Module. The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub μA power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01...
Reference: RBD-0725
Model: Emax Simon Series Burst Current: 40A (up to 10Sec) Input Voltage(V): up to 16V Constant Current: 30A BEC: 5V /2A Suitable Batteries: 2 ~ 4S
Reference: RBD-2142
Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.
Reference: RBD-0566
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Reference: RBD-0728
Working voltage: 5.5v-35v lipo 2s-5s Continuous current: 3A Instantaneous current: Min. 4A 20 seconds Output voltage: 5.25V +/-0.5V Suitable for: RC AirPlane Multirotor helicopter Special for FPV image transmission
Reference: RBD-2160
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0440
433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-2162
USB Type: Type-A to Mini-B Length: 1 meter/ 3.2 Feet Exclusively designed for Arduino boards. Compatible with Arduino Nano Larger Cable
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-0735
Supply Voltage: 7V.Processor: 32 Bit Cortex M4 CoreBus interface (UART, I2C, SPI, CAN).Firmware: Mission planner.Sensors: Gyrometer, Accelerometer, Barometer & MagnetometerMicro SD card to record flight data. RoboticsBD
Reference: RBD-1761
USB Type: Type-A to Type-B Weight: 80 gm. Length: 1m / 3.2Feet Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-0443
Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
Reference: RBD-0736
Model: 720 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Current: 0.1 A. Rated RPM: 48000. Max Speed: 50000 RPM. Wire Length: 5cm Prop. Length: 55mm
Reference: RBD-2195
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-0741
Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards
Reference: RBD-2196
USB Type: Type-A to Type-B Weight: 26 gm. Length: 50 cm Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-0743
Wheelbase: 550mm Weight: 550g/720g(without/with gimbal) Adopts S800 upward tilt arm design – Plastic injection moduling Ensures hardness and lighter weight – Brushless gimbal compatible for FPV It comes with PCB center board of soldered The arm equips support ridges for better and faster forward flight. Features pre-threaded brass sleeves.
Reference: RBD-2198
Model: CH341 Series Main Chip: CH341B Dimensions in mm (LxWxH): 85 x 28 x 12 Weight (gm): 20 8-bit parallel in EPP or MEM mode
Reference: RBD-0748
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: RBD-2311
USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.
Reference: RBD-0824
Material: glass fiber Can connect 1-4 ESC. This has an T connector plug to connect a battery.
Reference: RBD-2315
Pin Pitch: 2.54mm Probe model: P75-E2 (pointed tip) Needle diameter: 1.3mm Needle sleeve model R75-3W Row pin number: 6Pin Row Number: Single row space between: 2.54mm
Reference: RBD-0825
Improved Locking Gold Plated Connectors tip Color: Red High-Quality built and Material Good resistance to Temperature & High Amp. Current
Reference: RBD-2362
Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit...
Reference: RBD-0826
PolyMax 3.5mm Gold Connectors 3.5mm sprung gold connectors handle the large current, 50A+ systems. perfect for 3500mAh or larger capacity batteries