Reference: RBD-0032

Arduino Nano

84 reviews

USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...

Reference: RBD-0320

MAX6675 Module + K Type Thermocouple Sensor (Arduino compatiable)

9 reviews

Internal integrated cold junction compensation circuit. RoboticsBD With a simple three serial SPI interface; Temperature signal can be converted into 12-bit digital Embedded thermocouple break detection circuitry. High impedance differential inputs. Operating Voltage(VDC): 3 to 5.5 Temperature Range(°C): 0 to +1024 Cold Junction Compensation Range(°C):...

Reference: RBD-0321

PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃

New PT-100 Temperature Sensor AvailableClick Here PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃

Reference: RBD-0227

JF-0530B Pull Push Type Electric Solenoid Electromagnet 10mm 5N DC6V

3 reviews

Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm

Reference: RBD-2056

PT-100 RTD Temperature Sensor 3 Wire 50cm

1 review

Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5s

Reference: RBD-1578

DT-06 TTL to WIFI Module

Support serial AT command Support re-programmable, OTA firmware update Seamless transparent transmission between serial and WiFi Built-in HTTP Web Server, support configure parameters by web page

Reference: RBD-1670

ESP8285 IR Infrared Transmitter Receiver Module WIFI Remote Control Switch

The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA

Reference: RBD-1812

WeMos D1 mini Pro – ESP8266 based WiFi Module 16MB

2 reviews

11 digital input/output pins Interrupt/PWM/I2C/one-wire 1 analog input(3.2V max input) 16M bytes(128M bit) Flash External antenna connector Built-in ceramic antenna New CP2104 USB-TO-UART IC

Reference: RBD-1821

NodeMcu Lua WIFI Board Based on ESP8266 CP2102 Module

9 reviews

Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled Arduino-like hardware IO Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLL, regulators, DCXO and power management units Onboard USB to serial chip to easily program and upload codes from the Arduino IDE Easy to use breadboard friendly form...

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

1 review

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-0282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: RBD-2131

S2 Mini V1.0.0 ESP32-S2 4MB FLASH 2MB PSRAM WIFI Development Board

ESP32-S2 based WIFI development board Features S2FN4R2 WIFI IC Equipped with 4MB FLASH and 2MB PSRAM Type-C USB connectivity 27 digital input/output pins with support for interrupt/pwm/I2C/single wire ADC, DAC, I2C, SPI, UART, USB OTG

Reference: RBD-0289

16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685

14 reviews

Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED

Reference: RBD-2677

0.28" LED Digital Voltmeter Ammeter with 100V/10A Measurement With 100A Shunt

Operating on a 5V DC power supply with a current consumption of less than 60mA, this 0.28-inch Digital Voltmeter Ammeter is a versatile tool for measuring voltage and current. With a testing range of 0-100V for voltage and 1-100A for current, this meter offers precise measurements with easy readability, even in dim light conditions.

Reference: RBD-0311

YF-S201 Hall Effect Water Flow Meter / Sensor

9 reviews

Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD

Reference: RBD-0814

Sonoff Basic R2- WiFi Wireless Smart Switch

31 reviews

The 2021 Model is Sonoff Basic R2 Support remotely turn on or off added devices. Support Max 8 timers tasks for each added device. Works with AMAZON ALEXA Works with GOOGLE ASSISTANT Also, Work with NEST Support numerous Wi-Fi smart switches one smartphone.

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

1 review

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-2804

SN04-N NPN NO 5mm Distance Detector Proximity Sensor Switch Module

Operating Voltage(V): 5 ~24 Current Consumption Max: 5 mA Detection distance(mm): 5 mm. Type of detection: Inductive. Cable Length: 145 cm. Response Frequency: 500Hz Max. Protection class: IP 67.

Reference: RBD-2806

K Type Thermocouple Temperature Sensor 100mm Probe 0‑400℃

K Type Thermocouple Temperature Sensor 100mm Probe 0‑400℃

Reference: RBD-0349

Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board

31 reviews

Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...

Reference: RBD-2845

PT-100 RTD High Temperature Sensor 3 Wire PT100 Probe 7x200mm

Waterproof analogue sensor with the high temperature working in the range from -200°C to 420°C. The output is resistance dependent on temperature. Probe length is 200 mm.

Reference: RBD-0350

STM32F103C8T6 Blue Pill Development Board

16 reviews

100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.

Reference: RBD-2940

MOSFET F5305S 4 Channel Pulse Trigger Switch Controller

The MOSFET F5305S 4-Channel Pulse Trigger Switch Controller is a versatile and robust module designed for controlling high-power devices through PWM input. This controller is perfect for managing the speed of motors, adjusting the brightness of light bulbs, and other applications requiring precise control. Based on the reliable F5305S MOSFET model, this...

Reference: RBD-0354

TSL2561 Luminosity & Infrared Light integrating sensor

Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD

Reference: RBD-2309

ESP8285 ESP-M2 Development Board

Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! This module contains an ESP8285, which is an ESP8266 processor with 1MB of FLASH memory already built in. You can use it just like an ESP8266, it's the same processor and WiFi The ESP8266 processor from Espressif is an 80 MHz microcontroller with a...

Reference: RBD-2489

Wiznet W5500 Mini Ethernet Network Module

1 review

Wiznet Compact W5500 Network Module - 10/100 Base T WIZ850io is a compact size network module that includes a W5500 (TCP/IP hardwired chip and PHY embedded), a transformer and RJ45. It can be used as a component and no effort is required to interface W5500 and Transformer. The WIZ850io is an ideal option for users who want to develop their Internet...

Reference: RBD-2651

Wemos D1 Mini V3

D1 Mini board with 4 MB flash memory and ESP8266 chipset. The board can be programmed with Arduino IDE, has the CH340 USB chipset and allows you to create IoT devices quickly and easily.

Reference: RBD-0396

Ultrasonic Transducer Waterproof Distance Measuring Sensor Module

10 reviews

Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD

Reference: RBD-2687

WeMos D1 mini Pro – ESP8266 based WiFi Module 4MB

Compact Wi-Fi development board for versatile IoT projects. Integrates ESP8266EX microchip for Wi-Fi connectivity and processing power. 4MB Flash memory for code storage. Supports Arduino, NodeMCU, and MicroPython programming environments. Ideal for beginners and experienced developers alike.

Reference: RBD-0126

Mini Smart Wifi Breaker

Automate your home appliances with this compact WiFi and Zigbee dual-protocol smart switch. Supports high power loads (16A or 10A options) for controlling various devices. Works with traditional 2-way switches for seamless integration into existing wiring. Remote control and monitoring from anywhere via smartphone app. Voice control compatibility with...

Reference: RBD-0432

JF-0530B Pull Push Type Electric Solenoid Electromagnet 10mm 5N DC12V

2 reviews

Iron Body Material High quality ultra-compact electric lock. RoboticsBD Rustproof, durable, safe, convenient to use. Suction which tightly sucks the iron, thus locking the door. Designed with the open frame type and mount board, high power. Easy to install for the electric door lock or other automatic door lock systems with the mounting board Applicable...

Reference: RBD-2887

NodeMcu Lua ESP8266 WiFi Development Board CP2102 Driver - Type-C interface

The Development Kit based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board. Power your development in the fastest way combine with NodeMCU Firmware! R2 version had CP2102 USB-TTL instead, larger current support, slim board can put on breadboard. Programing it with Arduino IDE. A high-quality USB cable is essential for this board to...