Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0432
Iron Body Material High quality ultra-compact electric lock. RoboticsBD Rustproof, durable, safe, convenient to use. Suction which tightly sucks the iron, thus locking the door. Designed with the open frame type and mount board, high power. Easy to install for the electric door lock or other automatic door lock systems with the mounting board Applicable...
Reference: RBD-0704
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0715
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-0718
Model Type: Digital Radio Transceiver. Sensitivity: 1024. Bandwidth: 500 kHz. Default Operating Mode: Mode 2 (Left-Hand Throttle). No. of Channels: 6. Operating Voltage: 12V DC (1.5AA x 8 Battery) (not included).
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0719
Bandwidth (KHz): 500. RF Range (GHz): 2.40 ~ 2.48. No. of channels: 6. Remote controller weight (gm): 400. Power: 6V (1.5V AA*4). Antenna Length: 26mm * 2 (dual antenna). Transmitting Power: ≤ 20dBm. RF Receiver Sensitivity: -105dbm. RoboticsBD
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0725
Model: Emax Simon Series Burst Current: 40A (up to 10Sec) Input Voltage(V): up to 16V Constant Current: 30A BEC: 5V /2A Suitable Batteries: 2 ~ 4S
Reference: RBD-0736
Model: 720 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Current: 0.1 A. Rated RPM: 48000. Max Speed: 50000 RPM. Wire Length: 5cm Prop. Length: 55mm
Reference: RBD-0728
Working voltage: 5.5v-35v lipo 2s-5s Continuous current: 3A Instantaneous current: Min. 4A 20 seconds Output voltage: 5.25V +/-0.5V Suitable for: RC AirPlane Multirotor helicopter Special for FPV image transmission
Reference: RBD-0750
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-0817
Step Angle Step Angle: 1.8 ° Current: 2.8 A/Phase Holding Torque: 10.1 N-cm Detent torque: 3.6 N.cm (Maximum) Lead Wires: 4 Shaft diameter: 8.00 mm
Reference: RBD-0735
Supply Voltage: 7V. Processor: 32 Bit Cortex M4 Core Bus interface (UART, I2C, SPI, CAN). Firmware: Mission planner. Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer Micro SD card to record flight data. RoboticsBD
Reference: RBD-0818
17kg large torque. 15 kg·cm (208 oz·in) @6V 17 kg·cm (236 oz·in) @7.4V Full metal gear 180 degree rotation Using high-precision potentiometer with new design Convenient plug-in wire
Reference: RBD-2182
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below.
Reference: RBD-0819
17kg large torque. 15 kg·cm (208 oz·in) @6V 17 kg·cm (236 oz·in) @7.4V Full metal gear 270 degree rotation Using high-precision potentiometer with new design Convenient plug-in wire
Reference: RBD-2534
3D-printed robotic arm with 4 stepper motors and 1 servo motor for precise control Robot arm size: approximately 25 x 13 x 29 cm Features claws for easy gripping Includes all necessary 3D-printed parts and motors The color and claw mechanism of the Robotic arm may vary as our stock rotates. Current stock comes as assembled.
Reference: RBD-0420
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. RoboticsBD Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 60mA
Reference: RBD-0741
Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards
Reference: RBD-2695
Custom 3D-printed enclosure designed specifically for the US-015 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. Features two screw holes for convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-0743
Wheelbase: 550mm Weight: 550g/720g(without/with gimbal) Adopts S800 upward tilt arm design – Plastic injection moduling Ensures hardness and lighter weight – Brushless gimbal compatible for FPV It comes with PCB center board of soldered The arm equips support ridges for better and faster forward flight. Features pre-threaded brass sleeves.
Reference: RBD-0912
Model: 8020 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Rated RPM: 39000. Wire Length: 6cm Prop. Length: 55
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-0748
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: RBD-0913
High-Quality Pump Operating Voltage 12VDC Air pump rate: 4 LPM Current Consumption: 300mA Low Noise Operation Durable and Longer Lasting
Reference: RBD-0824
Material: glass fiber Can connect 1-4 ESC. This has an T connector plug to connect a battery.
Reference: RBD-0936
High-Quality Pump Operating Voltage: 24VDC Flow Rate: 1100GPH Outlet Diameter 19mm