Reference: RBD-1639

12V DC Long-Stroke Linear Actuator 300mm

1 review

Extends up to 300mm Powerful & Long Stroke Durable Construction Versatile Applications Automatic Control Features

Reference: RBD-2045

DIY D2-1 Intelligent Line follower/Tracking Smart Car Kit

Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included

Reference: RBD-0392

Ardumoto Shield L298P Motor Driver

L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD

Reference: RBD-2251

BALA-C PLUS ESP32 Self-Balancing Robot Kit

ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38

Reference: RBD-0189

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Reference: RBD-0434

DRV8825 Stepper Motor Driver Module

5 reviews

Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD

Reference: RBD-1254

XiaoR STM32 Self Balancing Programmable Robot

Size: 202X85X200mm Weight: 1150 gram MCU: STM32F105 Motor Drive: LV8731 motor driver chip Charging Direct

Reference: RBD-2469

Brass Liquid Solenoid Valve - 12V - 1/2 NPS

Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition to your robotic gardening, aquarium, or pool project. There are two 1/2" (Nominal NPS) outlets. Normally, the valve is closed. When 12VDC is applied to the two terminals, the valve opens and water can flow. Unlike the plastic solenoid valve, this one does...

Reference: RBD-0121

LED - SMD RGB HL5011 (Pack of 5)

6 reviews

Reference: RBD-0435

A4988 StepStick Stepper Motor Driver Module

4 reviews

Supply Voltage : 8-35 VDC. Current : 1.0A  (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.

Reference: RBD-1253

Wuli bot Programmable Robot

1 review

Program Software: Mixly + XR Scratch(base on Scratch2.0) Input: Edge sensor, Button, IR receiver module, Ultrasonic sensor, Tracking sensor Output: Buzzer, RGBLED, Two motor port,OLED CPU: Arduino UNO R3 Power: 2Pcs 3.7V DC Lithium battery Control: WiFi control/IR remote

Reference: RBD-2513

5V Electromagnet - 25 Kg Holding Force - P40/20

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 25 Kg / 55 lb Approximate Pickup Weight: 5 KgEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and...

Reference: RBD-0195

Brand: RoboticsBD

25mW Infrared Line Laser Light

25mW Infrared Line Laser Light

Reference: RBD-0557

30A Mini VNH2SP30 Stepper Motor Driver Monster Moto Module For Arduino

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-1129

Brand: RoboticsBD

Otto Bot Complete

1 review

Complete Assembled  Plug and Play Open Source Design Compatible With Arduino IDE DIY Kit

Reference: RBD-2514

5V Electromagnet - 10 Kg Holding Force - P30/22

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 10 Kg / 22 lb Approximate Pickup Weight: 2 Kg / 4 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through...

Reference: RBD-0208

Off-Road Wheels - 130x60mm (Pair)

3 reviews

"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."

Reference: RBD-0573

DC 5V Stepper Motor with ULN2003 Driver Board 28BYJ-48

21 reviews

Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm

Reference: RBD-1252

Makeblock mBot Ranger 3-in-1 educational robot kit

Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes

Reference: RBD-2515

5V Electromagnet - 5 Kg Holding Force - P25/20

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 5 Kg / 11 lb Approximate Pickup Weight: 1 Kg / 2 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through...

Reference: RBD-0222

35mm Piezo Ceramic Elements Sound Sensor

15 reviews

Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound

Reference: RBD-0662

EasyDriver Shield Stepper Motor Driver V44 A3967 For Arduino

Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD

Reference: RBD-1313

Lynxmotion Johnny 5 Combo Kit

Indoor and Outdoor Tracked Robot Platform Designed for indoor or outdoor use and performs well on many different surfaces Its a very cool and completely functional model of the ever popular movie robot

Reference: RBD-2516

5V Electromagnet - 2.5 Kg Holding Force - P20/15

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 2.5Kg / 5.5lb Approximate Pickup Weight: 0.45 Kg / 1 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current...

Reference: RBD-0226

Brand: SparkFun Electronics

Camera Module - pcDuino V3 (2MP)

Camera Module - pcDuino V3 (2MP)

Reference: RBD-0684

Motor Driver - Dual TB6612FNG (1A)

9 reviews

CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1

Reference: RBD-1311

mDrawbot kit

mDrawBot is a 4-in-1 drawing robot kit  it can be assembled into 4 different drawing robots:  mScara. mCar.  mSpider.  mEggBot.

Reference: RBD-2518

Plastic Water Solenoid Valve - 12V - 1/2" Nominal

1 review

1/2" Nominal NPS Working Pressure: 0.02 Mpa - 0.8 Mpa Working Temperature: 1 ℃ - 75 ℃ Response time (open): ≤ 0.15 sec Response time (close): ≤ 0.3 sec Actuating voltage: 12VDC Actuating life: ≥ 50 million cycles

Reference: RBD-0241

LM35 Temperature Sensor

31 reviews

Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typical  LM35 (working) tested by...

Reference: RBD-0371

NAO V5 STANDARD EDITION

The result of a unique combination of mechanical engineering and software, NAO is a character made up of a multitude of sensors, motors and software piloted by a made- to -measure operating system: NAOqi OS. The pack includes: One NAO V5 (red or blue) 1 Charger and 1 battery 2 years of warranty 1 Choregraphe License Full SDK and API

Reference: RBD-0703

SSC-32 32Ch Servo Controller Lynxmotion Compatible

Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts

Reference: RBD-2517

6V Air Valve with 2-pin JST XH Connector

Here's a cool new valve for makers interested in pneumatic systems, hydraulics, inflatables, projects with compressed air, and the like. These air valves, also known by other names like, automatic bleeding valve or air release valve, are typically used to passively release air from a pressurized container.