Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1928
Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.
Reference: RBD-1172
Infrared Sensor Automatic Lighting Control Switch with lamp holder; convenient, safe & practical. Good solution for energy saving. You can conveniently let the light auto on/off. The switch can detect the human body's infrared, and use infrared to control the load. Easy to install. Strong anti-interference ability Suitable for corridor, toilet,...
Reference: RBD-1173
Input Current : 100A Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Meet UL94-V0 flame retardant properties
Reference: RBD-1947
Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg...
Reference: RBD-1948
Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off Note: Relay might be...
Reference: RBD-1973
Brand: DFRobot
Easy-to-use Low-cost expansion board for micro:bit Leads out all IO ports of micro:bit Specially-designed port for “HuskyLens AI camera”. This board can be used to Provide stable 5V power supply for HuskyLens to make it run steadily in all modes. Silkscreens on the back clearly indicate the functions of all interfaces
Reference: RBD-2039
Product Name:DY-SV5W Voice Playback Module Product Number:DY-SV5W Work Voltage:DC 5V Working Temperature range:-20℃~85℃ Working Humidity range:0%-95%RH Size :35*35*4.5mm
Reference: RBD-2064
TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. Note: If you want to buy the cheaper recycled SIM800L Module Click here.
Reference: RBD-1203
Distance measuring range: 10 cm to 80 cm Output type: Analog voltage Output voltage differential over distance range: 2.05 V (typical) Update period: 38 ± 10 ms
Reference: RBD-1210
Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz
Reference: RBD-1211
Single supply: 2.7-36v Size of photodiode: 2.29mm x 2.29mm Internal feedback resistor: 1MΩ
Reference: RBD-1380
Sharp GP2Y0A02YK0F IR Range Sensor - 20 cm to 150 cm Infrared range finder 20cm (~8") to 150cm (~60") Distance measuring range: 20 cm to 150 cm (8″ to 60″) Output type: Analog voltage Output voltage differential over distance range: 2.05 V (typical) Update period: 38 ± 10 ms
Reference: RBD-2145
L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators
Reference: RBD-0738
Resolution: 5 MP Interface Type: CSI(Camera Serial Interface) Dimensions: 25x23x8 (LxWxH) mm Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video Fully Compatible with Raspberry Pi 3 and 4 Model B Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
Reference: RBD-2208
2x 18650 Lithium Battery Shield V8 Mobile Power Expansion Board Module 5V/3A 3V/1A Micro USB for Arduino ESP32 ESP8266 Output port: USB or expansion port Output parameter 5V / 3A or 3.3V / 1A. Conversion efficiency up to 95% Input port: MicroUSB
Reference: RBD-2212
Directly plug antenna interface. I2C bus communication. Multi-capacitor combined filter. Blue LED power indicator. High sensitivity(low noise RF input amplifier). High power auto gains control AGC circuit.
Reference: RBD-1645
Voltage operation: 2.7V-5V Measuring distance: 4 to 50 cm Output: Digital (I/C) / Analog Output Sensor: Infrared LED and CMOS image sensor
Reference: RBD-2228
Working voltage: 2.3V-5.5V. Working temperature range: -40 ~ + 105. Onboard 25MHZ (accuracy of 50ppm) active crystal. On-board high-speed amplifiers
Reference: RBD-2290
X, Y axis output is two potentiometers, can read the twist angle through AD conversion. Press the rocker downward, you can move a touch switch, for digital output, has been pulled up. The original OMRON button has long life and good handle. It is suitable for two degrees of freedom steering gear pan tilt control or other remote control proportional...
Reference: RBD-2291
Functional configuration: 2 PS2 game joysticks (2 analog voltages per channel) 1 digital level) 2 independent buttons (original button) Product Features: The X and Y axes output are two potentiometers, and the twist angle can be read by AD conversion. Press the rocker down to send a touch switch, for digital output, has been pulled up Original Omron...
Reference: RBD-2292
Onboard CAN transceiver SN65HVD230 Powered from 3.3V Features ESD protection Connecting MCUs to the CAN network Compatible with PCA82C250
Reference: RBD-1835
Input current (RMS): 50A. Work temperature: -25℃~+70℃. Storage temperature: -30℃~+90℃. Work voltage: 660V. Frequency range: 50Hz-1KHz.
Reference: RBD-2294
JQ6500 MP3 Voice sound module can play stereo MP3 files or standard mono audio files. The module has two different modes to operate in; serial communication mode (connecting to a microcontroller) or AD button control mode (module can be controlled with switches).
Reference: RBD-1836
Input Current : 0-30A Output Mode: 0-1V @ 30mA Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection Meet UL94-V0 flame retardant properties
Reference: RBD-0569
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-1913
Onboard LDO Voltage regulator Can be interfaced with 3V3 or 5V Microcontroller. Tap/Double Tap Detection Free-Fall Detection Analog output Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from the motor and other high current electronics Power LED
Reference: RBD-2318
The Speaker module is composed of a power amplifier and a loudspeaker. Sound size can be adjusted by the potentiometer on the circuit board. Enter different frequencies, the speakers produce different tones. Can be carried out by for Arduino encoding and DIY their music box!Product data interfaceusing anti plug,the two sides of the interface are...
Reference: RBD-2331
This is a rotary potentiometer module consisting of 8 adjustable potentiometers and the communication method is IIC interface. The module mainly uses 10K adjustable resistors. By rotating the potentiometer to change the size of the resistance value, then build a circuit to convert the change of resistance value to voltage change, read the output value...
Reference: RBD-2114
Multifunctional Expansion Board LM35 Temperature Buzzer for Arduino UNO Fully compatible with Arduino UNO interface Integrates multiple module functions Provides basic experimental modules for beginners Expansion ports for additional module experiments
Reference: RBD-2397
GPS Module NEO-6M Satellite Positioning Module for Arduino with MicroUSB
Reference: RBD-2459
Converts 5 – 30V down to a 0.8 – 29V output with adjustable current limit
Reference: RBD-2488
Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet 10BaseT/100BaseTX Ethernet PHY embedded Auto-Negotiation (Full-duplex and half duplex) Support Auto MDI/MDIX Simultaneously Supports to 4 independent sockets 0.18 µm CMOS technology 3.3V operation with 5V I/O signal tolerance Provide Serial Peripheral Interface (SPI MODE...