Reference: RBD-2083

Analog Temperature Sensor Module

Operating Voltage : 5v. Temperature measurement range : -55°C to 125°C. Measurement Accuracy : ±0.5°C.

Reference: RBD-1332

I2C Graphic 128x64 LCD Adapter

Adapter: Graphic 128x64 Communication: i2c 

Reference: RBD-2856

Brand: DFRobot

Solar Power Manager 5V

The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and application engineers. Solar Power Manager 5V is a small power and high-efficiency solar power management module designed for 5V solar panel. It features as MPPT...

Reference: RBD-2759

MicroSD Card Module

Allows MicroSD cards to be written and read

Reference: RBD-0409

4 Channel 5V Relay Board Module

No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...

Reference: RBD-2145

L298P Motor Driver Shield for Arduino

L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators

Reference: RBD-1970

Brand: DFRobot

Gravity: Speech Synthesis Module V2.0 (Support English and Chinese)

Version 2.0 More natural pronunciation Fewer pronunciation errors for polyphone characters No option of speakers

Reference: RBD-1973

Brand: DFRobot

IO Extender for micro:bit

Easy-to-use  Low-cost expansion board for micro:bit Leads out all IO ports of micro:bit Specially-designed port for “HuskyLens AI camera”. This board can be used to Provide stable 5V power supply for HuskyLens to make it run steadily in all modes. Silkscreens on the back clearly indicate the functions of all interfaces

Reference: RBD-1948

8 Channel 5V Relay Module

Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off Note: Relay might be...

Reference: RBD-2466

1.2-34V 5A Dc-dc Step-down CC/CV Xl4015 Battery Charger Led Driver With Volt, Amp & Power Meter

This XL4015-based voltage converter is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module with Constant Voltage and Constant Current control, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation.

Reference: RBD-2555

Humidity Sensitive Relay Module 5V

This is a self-contained switching module that energizes / de-energizes a relay based on the humidity level.   Just add 5V power and hook up the load you want to control then adjust the potentiometer to set the relative humidity level at which you want the relay to switch between ON / OFF. This type of module can be used for applications such as to...

Reference: RBD-2151

JoyStick Shield Module Robotics Control

2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V

Reference: RBD-0564

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-1947

8 Channel 12V Relay Module

Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg...

Reference: RBD-2039

DY-SV5W Audio Playback MP3 Module

Product Name:DY-SV5W Voice Playback Module Product Number:DY-SV5W Work Voltage:DC 5V Working Temperature range:-20℃~85℃ Working Humidity range:0%-95%RH Size :35*35*4.5mm

Reference: RBD-1684

Arduino Pro Mini PLC Relay Board

8 Channel DC 12V Pro mini Relay Shield Module PLC Timer Board for Arduino 

Reference: RBD-2454

MAX7219 8 Digit Led Tube Display Control Module

Power: 5V This module is compatible with 5V and 3.3V microcontrollers. Material: PCB + Electronic Components

Reference: RBD-2488

W5100 Ethernet Network Module for Arduino

Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet 10BaseT/100BaseTX Ethernet PHY embedded Auto-Negotiation (Full-duplex and half duplex) Support Auto MDI/MDIX Simultaneously Supports to 4 independent sockets 0.18 µm CMOS technology 3.3V operation with 5V I/O signal tolerance Provide Serial Peripheral Interface (SPI MODE...

Reference: RBD-2327

Brand: DFRobot

Self-powered Wireless Switch 433Mhz

In life, remote controllers can be seen everywhere, and most of them are inseparable from the battery. However, we often encounter problems when using the battery, for instance, it is troublesome to replace the battery, batteries are easy to corrode in a humid environment, or the waste batteries may cause serious environmental pollution. Do you know that...

Reference: RBD-2727

PCF8574 I2C I/O Expansion Module

Module can be used to expand the digital I/O of an MCU using the I2C bus.

Reference: RBD-2326

Brand: DFRobot

Gravity Analog Heart Rate Monitor Sensor (ECG) for Arduino

The DFRobot Heart Rate Monitor Sensor is used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG and output as an analog reading. An ECG signal can be extremely noisy so we have included an AD8232 chip which will generate a clear signal from the PR and QT Intervals. Using the Arduino IDE "Serial Plotter"...

Reference: RBD-0915

UART EM4100 RFID Card Reader RDM6300

Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design

Reference: RBD-2120

HW670 5A Current Sensor

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.

Reference: RBD-0273

Brand: Waveshare

Arduino WIFI Shield EMW3162

A1rduino WIFI Shield EMW3162 (module is not included)

Reference: RBD-1217

Nextion NX3224T024 - Generic 2.4" TFT LCD Touch Display

Nextion is a seamless Human Machine Interface (HMI) solution. Nextion provides a control and visualization interface between a human and a process, machine, application or appliance.  Nextion is mainly applied to Internet of thing (IoT) or consumer electronics field.

Reference: RBD-2328

SIM A7670C R2 4G LTE GSM Module Compatible with STM32 Raspberry Pi

The A7670 series is the LTE Cat 1 module that supports wireless communication modes of LTE-TDD/LTE-FDD/GSM/GPRS/EDGE. It supports a maximum 10Mbps downlink rate and a 5Mbps uplink rate. The A7670 series supports multiple built-in network protocols, which are suitable for main IOT applications such as telematics, surveillance devices, POS, industrial...

Reference: RBD-2240

LilyPad SMD LED Green Color

Wearable e-textile technology.  Designed with large sew tabs LED Green Color

Reference: RBD-2323

NeoPixel 5050 WS2812B 1Bit RGB LED with Integrated Driver

The WS2812B RGB LED Module is a small module with BIG color.  The module has a special LED on board that contains three separate LEDs – red, green, and blue – as well as a smart control IC that can individually drive each LED.  Each color has 256 intensity levels which allows the module to produce 24-bit color, or more than 16 million colors.  Each module...

Reference: RBD-0439

Arduino Android IOS HM-10 BLE Bluetooth 4.0 CC2540 CC2541 Serial Wireless Module

Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....

Reference: RBD-2340

2 Channel PWM Pulse Frequency Adjustable Duty Cycle Square Wave Rectangular Wave Signal Generator Module

2 Channel PWM Pulse Frequency Adjustable Duty Cycle Square Wave Rectangular Wave Signal Generator Module to generate square wave for experiment development. This is used to drive stepping motor drivers' square waves, Generate an adjustable pulse for MCU using, and Generate an adjustable pulse for controlling the relative circuit (PWM adjust lightspeed, etc).