Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1157
Wick Width: 3 mm (+/- 2) Length: 1.5 Meter Material: Copper
Reference: RBD-0212
Input: 110v or 240v A/C (50/60Hz) Cell Count: 2~3s Battery Type: LiPoly Output Current: 3 x 800mA
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-1158
Width: 10 mm Length: About 33m. Type: Polyimide Tape. Heat Resistance: 200℃. Thickness Tolerance: ±10% . One-side Self-adhesive.
Reference: RBD-0103
This is M177 NRF24L01 2.4GHz Antenna Wireless Transceiver Module. The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub μA power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01...
Reference: RBD-0927
Weight: 85 gm. Voltage : 11.1 V. Dimensions : 17 x 34 x 72(mm ). Max Continuous Discharge : 25 C(25 A). Balance Plug : JST-XH. Discharge Plug : XT-60.
Reference: RBD-1159
Removes all Solder Residue Low cost and high-quality Ideal replacement for the old sponges. Removes excess solders from soldering iron tips Provides extended tip life
Reference: RBD-0566
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Reference: RBD-0928
Voltage : 11.1V Constant Discharge : 30C(10.5A) Max discharge : 25C (10 sec) Dimensions : 74 x 34 x 22 (LxWxH)(mm ) Weight : 87 gm Charge Rate : 1-3C Recommended, 5C Max
Reference: RBD-1160
Brand new and high quality 10ml Pen Applicator with specially designed felt tip For rework and touch-up of SMT, SMD, and through hole solder joints Suitable for automotive, computer, telecom etc Flux flows smoothly for consistently secure and uniform solder connections with no mess Rosin residue is non-corrosive, non-conductive, non-clean, moisture...
Reference: RBD-0440
433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD
Reference: RBD-0929
Weight : 97 gm Voltage: 11.1V Capacity: 1500mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-1161
Premium Quality Soldering Wire/Lead Low Melting Point Weight: 20-22 Gram 0.8mm Known as Lead or Solder Wire Melting Temperature 180°C Approx. (Tested by RoboticsBD LAB) We suggest this solder wire/lead paired with this solder to make your soldering work easier. Check GOOT Original KX-60R Soldering Iron 45W Check GOOT Original Soldering Iron TQ-77 here
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-0930
Weight : 182 gm Voltage: 11.1V Capacity: 2200mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-1162
Net Content: 15g Paste Color: Brown Does not create High Smoke Does not create Foul/Bad Smell No Residual Waste High-Quality Soldering Additives & Activators for effective soldering Useful for general purpose soldering, electrical wires, components, and cables etc
Reference: RBD-0443
Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
Reference: RBD-0931
Weight : 190 gm Voltage: 11.1V Capacity: 3300mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-1166
Heavy-duty base to uphold the weight of Soldering iron Nickel-plated spring holder Spring holder provides substantial room for holding the soldering iron support
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-0919
Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: 1169
Please select your desired models from the list below.
Reference: RBD-0215
AC 100~240v or 12V DC input The cables come with a fitted fuse. Microprocessor controlled Li-ion, LiPo, and LiFe capable Input voltage monitoring. (Protects car batteries at the field) Battery break-in and cycling feature Data storage (Store up to 5 packs in memory) Internal resistance checker to see pack health Delta-peak sensitivity Individual cell...
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-1170
Made of high-quality material Suitable for cutting Aluminum and Copper Cuts wire up to a diameter of 3mm Fully Polished Well finished cutting edges
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. RoboticsBD Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-1171
New Solder Sucker Desoldering Pump Tool Removal Vacuum Soldering Iron Desolver Metal Body, high sucting power, light weight. RoboticsBD Back pull pattern for the inner spring instantaneous suction is strong. Slimline outlook, airtight structure allow one-headed operation. All metal construction is ideal for heavy use including production re-work and...
Reference: RBD-0696
Voltage : Input through (USB) DC 5V Output via (DC Round Pin) : DC 12V Color: BLACK Input / Output Current: Maximum Input 0.6 Easier for installation save time and money Easy to use.
Reference: RBD-1181
Rubber handle Heavy-duty cutting tip Electric resistance up to 1000 Volts
Reference: RBD-0494
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: STD-120200
Reference: RBD-1182
High Quality Plastic body High suction power Teflon nozzle Easily replaceable nozzle Easy to clean and maintain
Reference: RBD-0963
Current and voltage display in turn, easy and comfortable to use. Small and portable, do not need other power supply. Measuring range: DC 3V – 9V / 0 – 3A (up to 5A ) Portable Device Interface: USB2.0, USB3.0 Product Weight: 0.025 kg Two output ports