Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

1 review

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-2198

CH341 USB Programmer

Model: CH341 Series Main Chip: CH341B Dimensions in mm (LxWxH): 85 x 28 x 12 Weight (gm): 20 8-bit parallel in EPP or MEM mode

Reference: RBD-2294

JQ6500 V2.1 MP3 Player Module

JQ6500 MP3 Voice sound module can play stereo MP3 files or standard mono audio files. The module has two different modes to operate in; serial communication mode (connecting to a microcontroller) or AD button control mode (module can be controlled with switches).

Reference: RBD-0288

GY-801 - Multi Sensor Board

1 review

Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v

Reference: RBD-2307

Stereo Enclosed Speaker 3W 8Ω

1 review

This speaker is a great addition to any audio project where you need 8 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm...

Reference: RBD-2311

USB To Serial Cable TTL 4 Pin Rs 232 UART Converter Adapter Programming Module

1 review

USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.

Reference: RBD-0311

YF-S201 Hall Effect Water Flow Meter / Sensor

9 reviews

Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD

Reference: RBD-2315

Pogo Pin Probe Clip - 6 Pins with 2.54mm

1 review

Pin Pitch: 2.54mm Probe model: P75-E2 (pointed tip) Needle diameter: 1.3mm Needle sleeve model R75-3W Row pin number: 6Pin Row Number: Single row space between: 2.54mm

Reference: RBD-2318

Sound Output Module Speaker Module Microphone Sensor Module Sound Sensor for Arduino

The Speaker module is composed of a power amplifier and a loudspeaker. Sound size can be adjusted by the potentiometer on the circuit board. Enter different frequencies, the speakers produce different tones. Can be carried out by for Arduino encoding and DIY their music box!Product data interfaceusing anti plug,the two sides of the interface are...

Reference: RBD-0312

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

1 review

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

Reference: RBD-2362

CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit...

Reference: RBD-0430

Line Follower Sensor- 8 Array

12 reviews

Operating voltage: 4.5V to 5.0 V Output format: 8 Analog and Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD

Reference: RBD-2412

USB ASP AVR Programming Device for ATMEL Processors Arduino

1 review

Compatible Chips:ATMega Series Tiny Series Classic Series CAN Series PWM Series You can also use this to recover your Arduino Bootloader

Reference: RBD-2541

Brand: DFRobot

Gravity: Voice Recorder Module

This is the latest voice recorder module with integrated record and play functions. Easily record your voice by pressing the record button, speaking and then releasing the button when finished. The module is able to playback 10 seconds in total. Connect an 8Ω 3W speaker or an external active speaker for voice output. The module also has a 3 pin digital...

Reference: RBD-2413

FTDI Basic Breakout USBTTL 6PIN 5V Module Fio/Pro/RGB/Lilypad Programmer

Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...

Reference: RBD-2691

Through-Hole Speaker 15mm diameter - 2kHz range

Compact 15mm speaker for integrating sound into space-constrained projects. 2kHz frequency range suitable for basic audio applications. Through-hole mounting for easy integration with circuit boards. Handles up to 0.5W of power for moderate sound output.

Reference: RBD-0320

MAX6675 Module + K Type Thermocouple Sensor (Arduino compatiable)

9 reviews

Internal integrated cold junction compensation circuit. RoboticsBD With a simple three serial SPI interface; Temperature signal can be converted into 12-bit digital Embedded thermocouple break detection circuitry. High impedance differential inputs. Operating Voltage(VDC): 3 to 5.5 Temperature Range(°C): 0 to +1024 Cold Junction Compensation Range(°C):...

Reference: RBD-2416

WEMOS CH340G Breakout 5V 3.3V USB to Serial Module

5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver

Reference: RBD-2692

PCB Mount Mini Speaker Breadboard-Friendly - 8 Ohm 0.2W

Breadboard-Friendly PCB Mount Mini Speaker - 8 Ohm 0.2W 1.1" (~30mm) diameter speaker with 8 Ohm impedance Perfect for breadboard-based audio projects Durable plastic casing, lightweight design Power handling: Nominal 0.1 Watts, Maximum 0.2 Watts

Reference: RBD-0321

PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃

New PT-100 Temperature Sensor AvailableClick Here PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃

Reference: RBD-2425

Shielded Blue USB Type-C Cable 30cm for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-2693

5 cm Speaker - 8 Ohm 0.5W

Compact 5cm speaker for integrating audio into various projects like radios, amplifiers, and robots. 8Ω impedance and 0.5W power handling for compatibility with common audio circuits. Lightweight and space-saving design for versatile integration.

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

1 review

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-2427

USB Type-C Cable 1meter for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-2694

4cm Thin Speaker - 8 Ohm 0.5W

Incredibly thin (just over 4mm) 4cm speaker for adding sound to projects with severe space constraints. 8Ω impedance and 0.5W power handling for compatibility with low-power audio circuits. Ideal for applications like portable devices, greeting cards, or space-limited enclosures.

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

1 review

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-2463

Programmer Testing IC Test Clip Black SOIC8/SOP8 Flash Chip IC Test Clamp

The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...

Reference: RBD-2718

PAM 8610 Digital Stereo Class-D Amplifier Board 2x15W Output

Dual-Channel Stereo Output Run-on 7V to 15V power Supply 32 Steps DC volume control has a +32dB to -75dB range. 40 pin QFN 6 x 6 mm package. Much higher efficiency in terms of cost and performance than competitors’ ICs

Reference: RBD-0344

Weighing Sensor 24 Bit Load Cell Amplifier HX711

13 reviews

Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD

Reference: RBD-2655

ST-LINK/V2 CN In-Circuit Debugger/Programmer for STM8 and STM32

1 review

5V power supplied by a USB connector USB 2.0 full speed compatible interface USB standard A to mini B cable 1.65V to 5.5V application voltage supported on SWIM interface SWIM low speed and high-speed modes supported Made in China To upgrade the programmer using STM32CubeProgrammer you need to enable the "Shared" options. This product is a clone and might...

Reference: RBD-2724

MAX4466 Electret Microphone Adjustable Amplifier Module

The MAX4466 Electret Microphone Module is a convenient and sensitive audio sensor solution designed for capturing sound waves and converting them into electrical signals. This module incorporates the MAX4466 electret condenser microphone and an integrated amplifier circuit, making it well-suited for applications requiring clear and amplified audio capture.

Reference: RBD-0348

Heart Rate Pulse Sensor Module For Arduino

18 reviews

A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....