Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2682
Double H bridge, which can drive two DC motors at the same time, single 7A current, high power; Wide voltage input 6.5V ~ 27V ; Signal optocoupler isolated input, can be directly controlled by IO port, free from interference; Undervoltage protection to prevent instantaneous high current burning of the module; High-power TVS and electrostatic bleeder...
Reference: RBD-2721
The Solar Panel Multimeter is a sophisticated instrument engineered for accurate testing of photovoltaic panels. It offers comprehensive measurements to assess critical parameters such as the maximum power point and open-circuit voltage of solar panels, providing valuable insights into panel quality and performance.
Reference: RBD-2792
This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors, but keep in mind you might need to use some debouncing code, as the sensor...
Reference: RBD-0221
Capacitor 0.01uF 100V Metallised polyester capacitors with epoxy coating Excellent heat and solvent resistance Suitable for coupling and decoupling applications Self-healing properties
Reference: RBD-0358
Dimensions: 11×15 x 2 (L x W x H) mm Weight: 1gm Mutual transform between 5V TTL and 3.3V TTL Two channels of logic and high voltage low voltage logic can two-way transform Portable and lightness, with 2 rows 4 pin contact pins
Reference: RBD-0533
Brand: Siemens Simatic S5 Part No: 6ES5 465-4UA12Type: Analog InputMade in GermanyRobotics Bangladesh
Reference: RBD-0601
Xilinx Platform USB Download Cable Jtag Programmer FPGA CPLD C-Mod XC2C64A M102
Reference: RBD-0891
Rugged chrome-plated metal pushbutton with red LED ring Latching design for maintaining the switch state Built-in resistor for LED Supports 3 to 6V for LED operation IP65 and IK08 protection ratings Durable stainless steel and chrome-plated brass construction
Reference: RBD-1303
Cell Quantity: 6 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC Dimensions: 92 x 57 x 15 mm
Reference: RBD-1339
With LCD display which powered by 1*LR44 battery (included) Zero settings at any position Measuring Range 0-150m (0-6") **Although the manufacturer claims that it is made of carbon fiber, we believe it is actually made of ABS plastic.
Reference: RBD-1378
Brand new Material: PP Color: Blue Size: approx. 300*220mm
Reference: RBD-1637
4mm Banana Plug Jack Socket Male Female Binding
Reference: RBD-1702
Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-2044
Model: ESP32-CAM-MB Color: Black Chipset: CH340G Connectivity Technology: USB Note: The camera module is not included with the board.
Reference: RBD-2056
Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5s
Reference: RBD-2219
ESP32-IO shield Compatible with RoboticsBD ESP32 Core board Brings out all the pins of RoboticsBD ESP32 Core board 2 rows of 2.54mm pin headers for connecting other sensors Power supply circuit for RoboticsBD ESP32 Core board DC 7-12V voltage input DIP switch for controlling the power
Reference: RBD-2304
This is the 24 LED NeoPixel Ring, a small chainable 86mm outer diameter board equipped with 5050 WS2812 RGB LEDs. The WS2812s are each addressable as the driver chip is located inside the LED. Each NeoPixel Stick has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and requires 5 V.
Reference: RBD-2317
The is a 4 way navigation switch (north, south, east, west) with a center push. Think of it as a mini joystick. Whilst the pins don’t align perfectly to a 2.54mm grid, it can be made to fit into a breadboard or perfboard by bending the pins.
Reference: RBD-2345
Description: It is an 8051 microcontroller development board, fully compatible with WIN10/XP 32/64-bit operating system. A USB cable can fully realize program/serial communication. Its accessories include a blue screen with backlight LCD1602, infrared remote control, integrated infrared receiver and other accessories, which give full play to the...
Reference: RBD-2375
Rockchip RK3399(28nm HKMG Process) 6-core ARMR64-bit processor 4GB LPDDR4 SDRAM, 16GB EMMC Flash HDMI output, 26-pin headers, LCD connector, 2USB 2.0, 1USB 3.0, 1*USB 3.0 TYPE-C, mini PCIE connector, etc. Support for dual cameras, binocular vision ranging, power management, TF card storage, SATA and SSD expansion, LED indicator Low-level peripherals...
Reference: RBD-2398
This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices
Reference: RBD-2558
This is a mini Laser light module with onboard triode current amplifier circuit, it gets only 1.3mA from the SIG pin so it is compatible with much more MCU. Note: For safe use, the module must not directly illuminate human eyes or irradiate human body for a long time. Features: - Output wavelength: 650nm - Working voltage: 4.75-5.5V - Working current:...
Reference: RBD-2626
Brand: RoboticsBD
Accurate People Detection: Utilizes advanced Time-of-Flight (TOF) technology for reliable people detection. Wide Applications: Ideal for security, smart buildings, robotics, and more. Advanced Features: Offers high accuracy, fast response time, and various data processing options. Easy Integration: Seamlessly integrates into existing systems. Reliable...
Reference: RBD-2672
MCP3008 is one of the famous Analog to Digital converter IC. This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy to use, and uses SPI so only 4 pins are required. We chose this chip as a great accompaniment to the Raspberry Pi computer, because its fun to have analog inputs but the Pi does...
Reference: RBD-2710
Why is an analog eyeblink sensor better than a digital eyeblink sensor? Currently, most eye blink sensors on the market are digital. they can only distinguish between the eye being fully closed or fully open, unable to detect partial blinks or quick blinks. However, the analog sensor provides waveforms. By analyzing analog values, you can detect full...
Reference: RBD-2753
The UTL8200 Series is designed for users requiring a DC load with a compact form factor which is widely used in basic applications such as product production line and maintenance. Small size, easy operation, rich testing functions and modes, support for dual-channel independent testing, the standard RS-232 interfaces for remote communication to meet your...
Reference: RBD-2754
The L298N 4WD Motor Driver is a versatile and robust H-bridge driver module designed for controlling DC motors with ease and precision. With its compatibility with 3.3V microcontrollers and support for popular platforms like Arduino and STM32, this module offers flexibility and convenience in motor control applications.
Reference: RBD-2832
Designed for use as an endstop for 3D printers but it can be used for other contact detection applications as well.
Reference: RBD-0534
Brand: Siemens Simatic S5 Part No: 6ES5 922-3UA11Type: CPUMade in GermanyRobotics Bangladesh
Reference: RBD-0602
Proface HMI Cable GPW-CB02 Robotics Bangladesh ---------------------------------------------------------- এই ক্যাবলটি আমাদের কাছে বিক্রির জন্য স্টকে নেই। কিন্তু আপনার PLC তে কোন সমস্যা অথবা প্রোগ্রামিং করার প্রয়োজন হলে আমাদের সাথে যোগাযোগ করতে পারেন। Please Contact: 01705-760637