Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0265
Printing method: Thermal dot printing Printing speed: 50 - 80mm/s Resolution: 8 points/mm, 384 points/line Effective print width: 48mm Character set: ASCII, GB2312-80 (Chinese)
Reference: RBD-0817
Step Angle Step Angle: 1.8 ° Current: 2.8 A/Phase Holding Torque: 10.1 N-cm Detent torque: 3.6 N.cm (Maximum) Lead Wires: 4 Shaft diameter: 8.00 mm
Reference: RBD-1154
Specification: Magnification: 1000X Light source: 8 LED lights Resolution: 1920×1080, 640*480 Pixel: 30W Focal length: 3-40mm manual adjustment Support Android 4.2 or above/widows/Mac system
Reference: RBD-1951
High hardness, Corrosion protection. Waterproofness and High precision. The mode of its output signal:0-5V(Voltage signal). supply voltage: DC 12-24V. Power consumption:Voltage MAX≤0.3W. Start wind speed:0.4-0.8m/s.
Reference: RBD-0238
This is a mini Arduino based on-screen display board. It's tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible. It's main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader, and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin...
Reference: RBD-0523
Module Power: 5.00V Module Size : 43 x 32mm(1.69×1.26″) Measuring Range :0 – 14PH Measuring Temperature: 0 – 60 ℃ Accuracy : ± 0.1pH (25 ℃)
Reference: RBD-1366
DT8380FC Infrared Thermometer Item no.: DT8380FC Temperature Range: -50~380°C/-58~716°F Measuring Accuracy: ±2% or 2C Distance Ratio: 12:1
Reference: RBD-0579
Quad-band 850/900/1800/1900MHz GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load) GPRS mobile station class B Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands) Supports charging control for Li-Ion battery Supports Real-Time Clock Integrated GPS/CNSS and supports A-GPS Low power consumption, 10mA in sleep...
Reference: RBD-1075
Microprocessor controlled Delta-peak sensitivity Individual cell balancing LiIon, LiPoly, and LiFe capable NiCd and NiMH capable Large range of charge currents Storage charge function Time limit function Input voltage monitoring (Protects car batteries in the field) You need at least a 12V 6A Power Adapter to Power it. You can purchase it separately. Link
Reference: RBD-1527
Based on ATmega32 8 Bit microcontroller USB external programmer Included Datasheet, Manual, Software & Sample codes All Port pins pins available for peripheral interfacing
Reference: RBD-1665
Great for Starting with Arduino Programming A variety of components are included in this pack to try out different projects. The kit comes with quality components assured by RoboticsBD All-in-one kit, a great starter kit for learning to code. Microcontroller ATmega328
Reference: RBD-1837
58mm embedded thermal printer 60mm/s print speed Clear printing high efficiency Direct thermal printing
Reference: RBD-1869
This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen. Adjustable vertical displacement, and with instructions. With automatic, regular and one-shot modes, easy to capture the moment waveform. Available rising or falling edge trigger. Observable previous trigger waveform (negative delay). Can freeze at any...
Reference: RBD-1228
Input Power: 90-132VAC/180-264VAC,6.5A/4A,50/60Hz Output Power: 24VDC , 14.6A +Adjustable
Reference: RBD-0931
Weight : 190 gm Voltage: 11.1V Capacity: 3300mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-1525
Can control up to 3 device 220V Model : T3EU3C Remotely control devices through a phone Turn on/off devices with Amazon Alexa and Google Assistant Touch control buttons for convenient operation Set a particular time to turn on/off devices Customize one or groups of SONOFF devices to turn on/off with a simple tap Allow you to manage devices when there is...
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: RBD-1680
Electric Bolt Lock 12VDC Ultra-Low Power Design, More Durable and more environmentally friendly. 500,000 times power lock durability High strength aluminum lock body, stainless steel bolt.
Reference: RBD-2395
mmWave human presence sensor. It uses motion target tracking and can detect up to 3 people.
Reference: RBD-0669
Without Servo Motor & Servo Horn Material: Metal Color: black, as picture shows Function: clamping object
Reference: RBD-1036
Model: F550 Frame Weight: 620gm(including landing gear) Moter Mounting Hole Diameter: 3 mm Landing Gear Material: ABS Arm Size: 220 x 55 mm Landing Gear Length: 200mm Takeoff weight: 1200-2400 grams
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-1222
DT8380FC Infrared Thermometer Item no.: DT8380FC Temperature Range: -50~380°C/-58~716°F Measuring Accuracy: ±2% or 2C Distance Ratio: 12:1 Product description: DT8380FC Infrared Thermometer
Reference: RBD-1716
Working Voltage: 5.0V Maximum Working Current: 100mA Data Interface Level: L<0.8V, H>2.7V, maximum voltage level 3.3V Particle Measurement Range: 0.3 ~ 1.0μm; 1.0 ~ 2.5μm; 2.5 ~ 10μm Note: Please purchase this adapter board to use it with Arduino and Raspberry Pi.
Reference: RBD-1829
0-9999 Ohm Simple Resistance Box Precision Variable Decade Resistor Instrument PT-100 Simulator Can be used to simulate PT-100 Sensor for calibration purpose
Reference: RBD-1970
Brand: DFRobot
Version 2.0 More natural pronunciation Fewer pronunciation errors for polyphone characters No option of speakers
Reference: RBD-0565
Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software. USB power supply and peripherals power phase are separate to protect computer security. All the signals are to-isolate which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc. Wide input voltage range: 12-24V, and with...
Reference: RBD-0305
LCD Type: TFT LCD Interface: SPI Touch Screen Type: Resistive Touch Screen Controller: XPT2046 Colors: 65536 Backlight: LED Resolution: 480*320 (Pixel) Dimensions: 84.91×56.54 (MM) Compatible with Raspberry Pi B, Raspberry Pi B+, Raspberry Pi 2 & Raspberry Pi 3
Reference: RBD-0553
Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
Reference: RBD-1562
Model: DP50V5A Input voltage range: 6.00-55.00V Output voltage range: 0.00-50.00V Output current: 0.000-5.000A Output power range: 00.00-250.0W
Reference: RBD-2722
Add computer vision capabilities to your project, without the coding! The Person Sensor includes a camera module pre-programed and connected over Qwiic... Person Sensor V1.1 by Useful Sensors
Reference: RBD-2772
Used to test and develop Chengdu Ebyte E83-2G4M03S wireless module. E83-2G4M03S-TB has been pre-soldered to E83-2G4M03S. Please refer to the module manual for detailed usage. All IO ports of the E83-2G4M03S wireless module have been led out. The module is equipped with CH340X serial port chip, which can directly carry out serial communication development....