Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0145
Dual output mode, analog output more accurate A fixed bolt hole for easy installation With power indicator (red) and digital switching output indicator (green) Having LM393 comparator chip, stable. Operating Voltage: 3.3V~5V
Reference: RBD-1347
TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.
Reference: RBD-1744
Neodymium Magnet Size: Rectangle Dimension: 40mm x 20mm x 2mm
Reference: RBD-1610
TMicroelectronics TIP142 NPN Darlington 10 A 100 V
Reference: RBD-1324
Operating voltage: 2.5V-5.5V Maximum output power: 3W x 2 PCB size is about: length 30mm width 22mm overall height after installed is about 16mm Built with switch Potentiometer, can adjust the volume & control power switch freely! Flexible assembly usage.
Reference: RBD-1569
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: RBD-1611
TMicroelectronics TIP142 NPN Darlington 10 A 100 V
Reference: RBD-2104
40P color jumper wires Length: 300mm Weight: 45 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use
Reference: RBD-1041
PCB Size: 60 x 20 x 13.5 (LxWxH)mm. Color: red, yellow, green LED Size: 10mm x 7. Brightness: Normal brightness. Voltage: 5V. Interface: common cathode red yellow green control.
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-2106
40P color jumper wires Length: 300mm Weight: 45 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use
Reference: RBD-2564
This MOSFET module with optoisolation uses the LR7843 N-Channel logic compatible MOSFET with ultra low Rds(on) for moderate to higher current low-side switching applications of up to 15A continuous. N-Channel logic compatible MOSFET with optoisolation and ultra low 3.3mΩ Rds(on)
Reference: RBD-1573
Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm
Reference: RBD-2566
With this High-Power MOSFET module you can easily use the double mosfet through the separate connections for power supply, switch pins and signal pins.The LED on the module indicates whether the MOSFET is switched on. This board is particularly useful for controlling a large LED strip (one color) or a motor (in one direction) by using. PWM.
Reference: RBD-2614
If you've ever wondered how to control the headlight of a car from a microcontroller, a MOSFET is what you need. The IRF5305 is a very common MOSFET with very low on-resistance and a control voltage (aka gate voltage) that is compatible with most 5V microcontroller or mechanical switches. This allows you to control high-power devices with very low-power...
Reference: RBD-1318
Low saturation voltage Over temperature protection High noise immunity Applications: Motor Drive & Control Operating Supply Voltage Up To 46 V Total Dc Current Up To 4 A Low Saturation Voltage Overtemperature Protection
Reference: RBD-2519
Small 1.5 – 3V DC motor with fan for science projects or general experimenting 3V DC motor with cable Soft 3-leaf fan bladeThe Jumper may become detached during shipping and require soldering with a soldering iron.
Reference: RBD-2726
2A 5V Charge Discharge Integrated Module 3.7V 4.2V for 18650 Lithium Battery Charging Boost Mobile Power Supply Charge and Discharge Protection Converter Protection PCB Board Module
Reference: RBD-2755
When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking) and are TO-220 package so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220s, but because of the very low Rds(on) of down to 70 mOhms (depending on the Vgs - check the...
Reference: RBD-0897
Durable and sturdy hardened mild steel construction Securely mounts 25GA 370 Series DC Gear Motor 1.6mm bracket thickness for enhanced strength 4.4mm bracket mounting slot size for versatile mounting options
Reference: RBD-1736
Locking On/Off Switch Green LED Power Indicator Voltage Swapping Switch on both rail Channel Its concave design will not waste your proto zone. Easy to install on a breadboard with Compact portable size
Reference: RBD-1768
Locking On/Off Switch Green LED Power Indicator Voltage Swapping Switch on both rail Channel Its concave design will not waste your proto zone. Easy to install on a breadboard with Compact portable size
Reference: RBD-2041
Model : KY-040. Type : Incremental Encoder. Cycles per revolution (CPR) : 20. Working voltage : 0 – 5V. Material : PCB + Brass. Mounting Nut Thread diameter: 6.6mm Weight : 10 gm.
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-1369
Lifetime: 30 million Rated voltage:125V Rated current: 5A Dissipation Power: IC Supply voltage: IC KW11-3Z bearing microswitch.
Reference: RBD-2196
USB Type: Type-A to Type-B Weight: 26 gm. Length: 50 cm Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-1555
AL6-A With LED 5Pin Self-locking Push Button Switch
Reference: RBD-2602
Connect shafts with 4mm to 6mm diameters Rigid design for high torque and low inertia Durable copper construction with integrated structure Maintenance-free, oil-proof, and corrosion-resistant Ideal for model cars, boats, robotics, and more
Reference: RBD-2653
2.8V-5.5V to ±12V DC Conversion Step Up Power Supply Module is straightforward. There is a 2.8 to 5.5 V DC input and the module outputs +12 V and -12 V DC dual power supply voltage with a current rating of a maximum 30 mA. Off course the current output is low but sometimes it suits in many situations where one is looking forward for a small boost...
Reference: RBD-1406
High-Quality cable One male and one female connector. Flat 30cm Servo Lead Extention (JR) Quality wire and connectors used. Great for larger planes with servos that experience high loads.
Reference: RBD-2692
Breadboard-Friendly PCB Mount Mini Speaker - 8 Ohm 0.2W 1.1" (~30mm) diameter speaker with 8 Ohm impedance Perfect for breadboard-based audio projects Durable plastic casing, lightweight design Power handling: Nominal 0.1 Watts, Maximum 0.2 Watts
Reference: RBD-0604
Effortless Connection: Connects 6mm motor shafts to Mecanum wheels for hassle-free assembly of your robotic projects. Durable Construction: Made from ABS plastic for long-lasting performance and reliability. Tool-Free Installation: Features a convenient top hole for easy attachment without requiring additional tools. Versatile Applications: Suitable for...