Reference: RBD-1021

PAM8406 5Wx2 Class D Digital Stereo Audio Power Amplifier Module Board

Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g

Reference: RBD-1762

Mini BD243 Bubble 9-12V Tesla Coil Electronics Wireless PCB Module

Input voltage(V): 9-12 It can produce high-temperature PCB board size(cm):  3.1 x 4 It is convenient for fans to install high efficiency Weight(g): 20This product is shipped as unassembled and requires soldering to be completed. You will need to do the soldering yourself.

Reference: RBD-2249

20mm 2.4Mhz Ultrasonic Mist Maker Fogger Atomizing Transducer

Made From High-Quality Materials. Electronic High-Frequency Oscillations (2.4MHz). Material: Ceramic, Wire Diameter: Atomizer: 2cm/0.79in; Sealing ring: 2.5cm/0.98in

Reference: RBD-0443

GPRS GSM SIM900 Arduino Shield

Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).

Reference: RBD-1065

Arduino CNC Shield V3

Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate...

Reference: RBD-2317

5-way Tactile Navigation Switch

The  is a 4 way navigation switch (north, south, east, west) with a center push. Think of it as a mini joystick. Whilst the pins don’t align perfectly to a 2.54mm grid, it can be made to fit into a breadboard or perfboard by bending the pins.

Reference: RBD-0832

Arduino MicroSD Card Module

Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g

Reference: RBD-2466

1.2-34V 5A Dc-dc Step-down CC/CV Xl4015 Battery Charger Led Driver With Volt, Amp & Power Meter

This XL4015-based voltage converter is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module with Constant Voltage and Constant Current control, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation.

Reference: RBD-2920

2.42 inch OLED Screen LCD Display Module 128x64 SSD1309 SPI 7Pin White

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-2832

Roller Lever Endstop Limit Switch Module

Designed for use as an endstop for 3D printers but it can be used for other contact detection applications as well.

Reference: RBD-2312

WS2812 RGB 4X4 Display

When it comes to adding colour to an electronics projects, these 4x4 NeoPixel Squares use WS2812 Addressable RGB LED’s to display up to 16777216 different colour combinations, with simple operations and built-in features to greatly enhance functionality. This makes them ideal as LED Displays for basic to intermediate Electronics projects, and despite...

Reference: RBD-2244

LilyPad Slide Switch

Wearable e-textile technology.  Designed with large sew tabs Slide Switch

Reference: RBD-2455

2.42" Inch OLED Display SSD1309 12864 SPI Serial Port For Arduino C51 White

2.42" Inch OLED Display SSD1309 12864 SPI Serial Port For Arduino C51 WhiteBrand: No BrandMetal Bracket to protect Display

Reference: RBD-2099

Touch Sensor Switch Module

Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins

Reference: RBD-0399

Graphic LCD 84x48 (Nokia 5110) Black on White for Arduino

Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us. 

Reference: RBD-0550

Voice Recognition Module Kit V3 (Elechouse)

Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output. RoboticsBD

Reference: RBD-2833

Impact Switch Collision Switch Sensor Module

Type: Vibration Sensors Output: Switching Transducer Dimensions: 25 x 14 x 6 (LxWxH) mm Weight: 3 gm

Reference: RBD-2737

AT24C256 I2C Interface EEPROM Memory Module

Chipset : AT24C256. Operating Temperature: -55°C to 125°C. Storage Temperature: -65°C to 150°C. The voltage on Any Pin with respect to the ground: -1.0V to 6.25V. Maximum Operating Voltage: 6.25V DC.

Reference: RBD-1973

Brand: DFRobot

IO Extender for micro:bit

Easy-to-use  Low-cost expansion board for micro:bit Leads out all IO ports of micro:bit Specially-designed port for “HuskyLens AI camera”. This board can be used to Provide stable 5V power supply for HuskyLens to make it run steadily in all modes. Silkscreens on the back clearly indicate the functions of all interfaces

Reference: RBD-2491

ATX Power Supply Breakout Board

ATX Power Supply Breakout Board 3.3V, 5V, 12V and -12V Output Terminals ATX power supply breakout board allows for easy connection to the outputs of a standard ATX style PC power supply with 20 or 24 pin connections. Easily supply power to your projects from a high-quality and inexpensive (ofter surplus) PC-style power supply. This board provides +3.3V,...

Reference: RBD-2149

50kg Half-bridge Experiments Body Scale Load Cell Sensor

Capacity (Kg): 50. Output Sensitivity (mv/v): 1.0±0.1. Nonlinearity (%FS): 0.03. Repeatability (%FS): 0.03. Input Resistance (Ω): 1000. Insulation Resistance (MΩ): ≥5000.

Reference: RBD-2302

PCA9548A I2C 8 Channel Multiple Extensions Development Board

Low Standby Current. 1-to-8 Bidirectional Translating Switches. I2C Bus and SMBus Compatible. 5-V Tolerant Inputs. Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II. Note : Product may vary in two variants TCA9548A &  PCA9548A

Reference: RBD-1910

8 Channel 12V Relay Module USB (PC Intelligent) Control Switch

Square onboard USB interface for connection stability The use of imported high-performance USB controller chip Use the special relay driver chip ULN2803, relay work more stable Military grade PCB board production Input voltage: DC 12 V Input Current: more than 300mA Connection : NC / COM / NO Note: Relay might be different from the picture as per stock

Reference: RBD-2094

DHT11 Digital Relative Humidity and Temperature Sensor Module

The module can detect the surrounding environment of the humidity and temperature High reliability and excellent long-term stability The output from the digital output Humidity measuring range: 20%~90%RH(0~50 degree (temperature compensation). Temperature measuring range: 0~+50degree. Humidity measurement accuracy: ±5.0%RH. Temperature measurement...

Reference: RBD-2458

250W 8A Buck Converter XH-M404 Adjustable DC-DC Step-Down Module XL4016

The XH-M404 Adjustable DC-DC Step-Down Module can can step-down the input voltage to a range of 1.25 – 36V at up to 8A.

Reference: RBD-1037

SIM808 GPRS/GSM+GPS Shield

Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.

Reference: RBD-0346

PN532 NFC RFID Read / Write Module V3 Kit

The PN532 is a highly integrated transmission module for contactless communication at 13.56 MHz including microcontroller functionality based on an 80C51 core with 40 Kbytes of ROM and 1 Kbytes of RAM. The PN532 combines a modulation and demodulation concept completely integrated for different kinds of contactless communication methods and protocols at...

Reference: RBD-2676

PWM Signal Generator Stepper Motor Speed Controller Driver Board

Suitable for use with a wide range of stepper motors and drivers. Can be integrated into a simple control platform with a stepper motor and DC power supply. Offers three selectable low-frequency signal options: high (5.4k-160kHz), middle (540-16.6kHz), and low (80-2.4kHz), adjustable via jumper settings. Capable of producing both pulse and PWM signals,...

Reference: RBD-2542

Brand: DFRobot

SIM808 GSM/GPRS/GPS IoT Board (Arduino Leonardo Compatible)

This is an SIM808 GSM/GPRS/GPS IoT Board based on Arduino Leonardo. The SIM808 with Leonardo mainboard is the latest development board for multi-purpose applications. The onboard SIM808 module includes an integrated quad-band GSM/GPRS and GPS satellite navigation module, and a 4 layer PCB integrates the microcontroller, microphone, headphone jack and...

Reference: RBD-2216

PCF8591 Module Analog to Digital / Digital-Analog Converter Module

Module chip using PCF8951 Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v) The module integrated photoresistor by AD collection precise value of the ambient light intensity Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition Module integrated 1 channel 0-5V voltage...