Reference: RBD-0267

Big Easy Driver - Stepper Motor Driver

1 review

Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...

Reference: RBD-0289

16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685

14 reviews

Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED

Reference: RBD-0392

Ardumoto Shield L298P Motor Driver

L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

1 review

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: RBD-0434

DRV8825 Stepper Motor Driver Module

5 reviews

Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD

Reference: RBD-0313

RC522 RFID Card Reader Module Kit Android NFC supported

47 reviews

Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

1 review

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-0557

30A Mini VNH2SP30 Stepper Motor Driver Monster Moto Module For Arduino

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

1 review

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-0384

MAX7219 Red Dot Matrix Module MCU Control Display Module DIY Kit For Arduino

7 reviews

Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required

Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

29 reviews

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-1606

L297 Stepper Motor Controller IC

Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-1678

Big Easy Driver - Stepper Motor Driver

2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

14 reviews

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-1724

DC-5V-35V 5A PWM Motor Speed Controller

2 reviews

Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.

Reference: RBD-0393

JoyStick 5Pin Breakout Module For Arduino

26 reviews

Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD

Reference: RBD-1810

L293D Shield for NodeMCU V2

1 review

Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver

Reference: RBD-1912

L293D Motor Driver Module

1 review

New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

1 review

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-0399

Graphic LCD 84x48 (Nokia 5110) Black on White for Arduino

5 reviews

Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us. 

Reference: RBD-2209

Servo Motor Controller Driver Board 16 Channels High Accuracy MCU Software

16 channels PWM servo motor driver controller board module Supports USB interface, TTL serial port, and Bluetooth communication Bluetooth communication can connect to Android phone or PC software Master chip STM32 series, frequency 48MHz Size 43.5x36mmx12mm, operating voltage 5V USB, TTL3.3V, servo motor supply 5-7.2V Channel 16, PWM accuracy 0.1ms

Reference: RBD-2308

DC 3V-36V 15A Dual H-Bridge DC Motor Driver

This Dual Dc motor driver focuses on high efficiency and can withstand high current load, the maximum current up to 30A. 

Reference: RBD-0433

I2C LCD Adapter Module

41 reviews

5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.

Reference: RBD-0438

New ENC28J60 Ethernet LAN Network Module For Arduino

5 reviews

ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD

Reference: RBD-2369

LSC-6: Hiwonder 6 CH Bluetooth 4.0 Servo Controller Module for Robotics Arm

Built-in power switch High-performance CPU 16M high-capacity memory Built in Bluetooth 4.0 module Support TTL serial communication

Reference: RBD-0189

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Reference: RBD-2389

L298N Dual H-Bridge Motor Driver Module

1 review

This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.

Reference: RBD-2390

L298N PCB Driver Module Quad High-Power 4-Channel Smart Auto Motor Driving Board

Forward and reverse rotating :Forward and reverse rotating motor can be realized, can meet the needs of various working scenarios. Good production performance :Excellent production technology, not easy to cold joint, reliable and safe for you to use. Multiple good ability :With characteristics of strong driving ability, low heat dissipation and strong...

Reference: RBD-0552

A6 Pro Serial GPRS GSM Module Core Development Board

9 reviews

Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD