Reference: RBD-0015

Motor Shield L293D

93 reviews

2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...

Reference: RBD-0028

Arduino Ethernet Shield W5100

8 reviews

Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by for Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af...

Reference: RBD-0267

Big Easy Driver - Stepper Motor Driver

1 review

Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...

Reference: RBD-0108

USB Host Shield For Arduino UNO, MEGA, Compatible with Google Android ADK

11 reviews

Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...

Reference: RBD-0289

16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685

14 reviews

Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED

Reference: RBD-0159

LCD Keypad Shield for Arduino

5 reviews

Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...

Reference: RBD-0306

Torobot 32 Channel USB UART Servo Motor Controller

1 review

Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android

Reference: RBD-0376

L298N H-Bridge Dual Motor Driver, Stepper Motor Driver

134 reviews

Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes

Reference: RBD-0392

Ardumoto Shield L298P Motor Driver

L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

1 review

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: RBD-0434

DRV8825 Stepper Motor Driver Module

5 reviews

Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD

Reference: RBD-0313

RC522 RFID Card Reader Module Kit Android NFC supported

45 reviews

Low power consumption,Low cost, andCompact sizeRead and write chipFully integrated at 13.56MHz

Reference: RBD-0435

A4988 StepStick Stepper Motor Driver Module

2 reviews

Supply Voltage : 8-35 VDC. Current : 1.0A  (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

1 review

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-0557

30A Mini VNH2SP30 Stepper Motor Driver Monster Moto Module For Arduino

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

1 review

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-0573

DC 5V Stepper Motor with ULN2003 Driver Board 28BYJ-48

21 reviews

Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm

Reference: RBD-0346

PN532 NFC RFID Read / Write Module V3 Kit

3 reviews

The PN532 is a highly integrated transmission module for contactless communication at 13.56 MHz including microcontroller functionality based on an 80C51 core with 40 Kbytes of ROM and 1 Kbytes of RAM. The PN532 combines a modulation and demodulation concept completely integrated for different kinds of contactless communication methods and protocols at...

Reference: RBD-0662

EasyDriver Shield Stepper Motor Driver V44 A3967 For Arduino

Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD

Reference: RBD-0348

Heart Rate Pulse Sensor Module For Arduino

18 reviews

A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....

Reference: RBD-0684

Motor Driver - Dual TB6612FNG (1A)

9 reviews

CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1

Reference: RBD-0353

0.96" Inch I2C OLED Display Yellow

9 reviews

Driver IC: SSD1306 Support wide voltage: 3.3V-5V DC Communication: IIC Working temperature: -30-80 degrees. RoboticsBD

Reference: RBD-0703

SSC-32 32Ch Servo Controller Lynxmotion Compatible

Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts

Reference: RBD-0384

MAX7219 Red Dot Matrix Module MCU Control Display Module DIY Kit For Arduino

7 reviews

Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required

Reference: RBD-0742

Motor Driver 43A BTS7960

8 reviews

Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.

Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

29 reviews

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-1606

L297 Stepper Motor Controller IC

Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-1678

Big Easy Driver - Stepper Motor Driver

2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

14 reviews

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...