Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-0732
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. RoboticsBD Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-0652
Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. RoboticsBD
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum. RoboticsBD
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-0919
Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-0988
Hold 3 standard 18650 batteries. Wire Length: 15 cm. Output: 11.1 V. Dimension (Appro.) : 76 x 60 x 18 mm. Weight: 18 gm. High-quality plastic material
Reference: RBD-0989
Hold A standard 18650 batteries Wire : 15cm Output: 3.7v Dimension (Appro.): 76x20x20xmm Weight: 8gm High-quality plastic material
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-0702
It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-1754
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-0049
Description: Gainer is a simple board developed by Shigeru Kobayashi and the team at Gainer.cc. This board utilizes the Cypress PSoC CY8C29466 IC making it a great board for digital and analog projects where AtoD and DtoA is required. Simple USB interface for reprogramming - no external programmer needed.
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-0050
Description: The Maple is LeafLabs' 32-bit ARM development board. Coupled with the Maple IDE, the LeafLabs Maple line of development boards bring an Arduino style user experience to the world of powerful 32-bit ARM processors.
Reference: RBD-1771
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-1780
1. MINI USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 20 x 17.5 mm .
Reference: RBD-1781
1. Micro USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 16 x 14 mm .
Reference: RBD-1782
1. USB Type B Female ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 20 x 20 mm .
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-1783
1. USB Type A Male ( 4pin, A type, Male connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 32 x 15 mm .
Reference: RBD-1784
1. USB2.0 Type A Female ( 4pin, A type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 22 x 17 mm .
Reference: RBD-1785
1. USB3.0 Type A Female ( 9pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 28 x 25 mm .
Reference: RBD-1786
1. USB Type C Female ( 13pin, C type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 40 x 25 mm .
Reference: RBD-1855
Input voltage: 3-40V Output voltage: 1.5-35V(Adjustable) Output current: Rated current is 2A, maximum 3A Switching Frequency: 150KHz Operating temperature:Industrial grade (-40 to +85 ) Conversion efficiency: 92%(highest)
Reference: RBD-1885
AC Input Voltage: 100 ~ 240 V Output Voltage(V): 9V Output Current (Amp): 300mA Rated Frequency (Hz): 50 – 60. Cable Length: Approx 1.1m
Reference: RBD-1892
Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-1895
Brand: RoboticsBD
Input interface: USB Type-C Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.