Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0103
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications. Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch...
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0150
Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~+40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1367
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver
Reference: RBD-1368
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-1408
Type: CJMCU MINI USB AMS1117 MINI USB interface input 5V MINI USB outputs 5V and 3.3V DC power socket interface input 5V – 12V. DC power outlet output (5V label) 5V and 3.3V Weight: 2 gm.
Reference: RBD-1409
Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C. ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase...
Reference: RBD-1573
Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1842
Material: 12UM Stainless steel fiber Gram Weight: 0.2458g/m Strength: 2.8KGF. Length: 1m. Diameter(mm): 0.12. Resistance (Ω/m) : 27.
Reference: RBD-1911
LM358 chip onboard. 100 gain of the circuit design. 10K onboard adjustable resistance, you can adjust the magnification. Onboard power indicator. The chip has led major pin can be directly input and output signals.
Reference: RBD-0651
Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black.
Reference: RBD-2044
Model: ESP32-CAM-MB Color: Black Chipset: CH340G Connectivity Technology: USB Note: The camera module is not included with the board.
Reference: RBD-0653
Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)
Reference: RBD-0654
Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount. RoboticsBD
Reference: RBD-2076
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:5mm Color: Red + Green Beam Angle:150
Reference: RBD-2077
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:3mm Wavelength:571nm + 644nm Beam Angle:150
Reference: RBD-2078
No direction, any angle can trigger the work. Sensitivity switches can be selected for the trigger sensitivity according to circuit requirements. This switch is suitable for the trigger of the small current circuit. Component Type: SW-18015P Maximum voltage: 12V Rated Heating Current: 20mA
Reference: RBD-2080
Clean, good waveform driving ability, more than 15mA. Working voltage 3.3V-5 Output format: digital switching output (0 and 1) A fixed bolt holes for easy installation
Reference: RBD-2082
Dimension: 2.5 x 1.5 x 1.5 cm. Receiving angle: 90 °. Working voltage: 2.7 ~ 5.5V. Frequency: 37.9KHz Receiving range: 18m. Weight: 4 gm.
Reference: RBD-2083
Operating Voltage : 5v. Temperature measurement range : -55°C to 125°C. Measurement Accuracy : ±0.5°C.
Reference: RBD-2084
Power supply: 3 – 5V Good sensitivity The output format: Digital switching output (0 and 1) The comparator output signal is clean, good waveform, driving ability, more than 15mA. A fixed bolt holes for easy installation. Using a wide voltage LM393 comparator.
Reference: RBD-0829
Material: Aluminium M3 Screws Adjustable type servo arm Mounting Hole Spacing: 14mm Servo disc diameter: 20mm 25Tooth Weight: 2 gm
Reference: RBD-2085
Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH): 26 x 15 x 11 mm
Reference: RBD-2086
Operating Voltage: 5V Contact Resistance : 50mΩ max (initial) Electrically Life:100,000 cycles Environment temperature: -25°C to +105°C Operating Force: 180/230(±20gf) Seal temperature:250ºC-280ºC I/O pins: 3 pins
Reference: RBD-2087
Voltage 5V Photo interruption module triggers a signal when light is blocked between the opening of the sensor.