Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2265
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire. Motor Shaft coupling not included buy it here.
Reference: RBD-2727
Module can be used to expand the digital I/O of an MCU using the I2C bus.
Reference: RBD-2728
Temperature controller module for both heating and cooling applications.
Reference: RBD-2734
Bi-directional mux can handle analog and digital signals.
Reference: RBD-2320
The MG996R is an industry standard for high torque servos. The metal gearing gives a stalling torque of a high 10kg in a small package. The MG996R 360° has the ability to rotate continuously though 360° in both directions. This makes this servo perfect for robotics or even the rotation of camera sliders! Continuous rotation servos are like regular...
Reference: RBD-2735
Measures high-side current and voltage up to 3.2A @ 26VDC.
Reference: RBD-2321
Drive: 2WD Frame:1.5mm aluminum alloy structure, lightweight and high strength Working voltage: 4.5~6V Wheel Diameter:60mm
Reference: RBD-2736
2×8 connector, easy with the MCU mount. Jumper selectable can work in parallel or serial mode. On board 3.3 V LDO 1117, provides 800 mA current. 5 V power supply is powered by the target board. 12 MHZ crystal.
Reference: RBD-2737
Chipset : AT24C256. Operating Temperature: -55°C to 125°C. Storage Temperature: -65°C to 150°C. The voltage on Any Pin with respect to the ground: -1.0V to 6.25V. Maximum Operating Voltage: 6.25V DC.
Reference: RBD-2360
Model: MG90S Weight: 13 gm Operating voltage: 4.8V~ 6.6V Servo Plug: JR Stall torque @4.8V : 1.8kg-cm Stall torque @6.6V : 2.2kg-cm 360 Degree Continuous Rotation Note: The component, colour & shape of the motor may vary depending on our stock rotation. Continuous rotation servos are like regular hobby RC servos but modified to offer speed control...
Reference: RBD-2740
Precision 12-bit Digital-to-Analog converter with I2C interface
Reference: RBD-2369
Built-in power switch High-performance CPU 16M high-capacity memory Built in Bluetooth 4.0 module Support TTL serial communication
Reference: RBD-2741
Module mounts an 8MB serial flash chip for easy use with breadboards.
Reference: RBD-2382
The TEC1-12712 Thermoelectric Cooler 12A Peltier Module is the simple application of the Peltier Thermoelectric Effect. The module features 127 semiconductor couples in the area of 40mmx40mm which very effectively cools and heats up to 80°C. Thermoelectric coolers also are known as TEC or Peltier Module create a temperature differential on each side. One...
Reference: RBD-2757
N-Channel logic compatible MOSFET with optoisolation and low Rds(on).
Reference: RBD-2383
Model number: TEC1-12710 Operating Voltage: 12V Maximum Voltage- Umax (V) : 15V Maximum Current- Imax (A) : 10A Maximum Power : 120 W Power Cord: 25 cm.
Reference: RBD-2394
Smart Robot Rubber Wheel Support Stepper Motor and DC Motor Size:47*33.8*12mm Diameter: 48 mm D Shaft Size: 3 x 5mm Tire width: 12 mm Material: Rubber and ABS Plastic Suitable for mini Robots and Hobby kits. 1 pcs only
Reference: RBD-2760
RS422 interface, two-way communication. B Y Z A ultra far transmission 1000 meters The module has ESD 15KV protection. Onboard to increase the limit of 10 ohms current limiting current protection. Module with TVS diode. Anti lightning, peak voltage. The module has 120-ohm termination resistors, which can effectively reduce the interference of long-range...
Reference: RBD-0122
Designed for speed with four-wheel drive capabilities Reduce drag with two-wheel drive configuration N20 Gear Versatile Compact
Reference: RBD-2761
ICL8038 12V to 15V, Signal Generator, Medium/Low Signal, Frequency 10Hz-450KHz, Triangular/Rectangular/Sine Wave Generator, Module Working voltage: 12V ~ 15V Output: Triangular wave, Square wave and sine wave. Frequency range: 10HZ ~ 450kHz Low distortion sine wave: 1% Duty cycle range: 2% to 98% Low temperature drift: 50ppm / ℃ Triangular wave output...
Reference: RBD-2414
This tracking module adopts four tracking probes, and optimized spacing layout. The inner two probes can accurately identify the black line. The outer two probes can assist the inner probe to identify the black line and provide early warning. The car can recognize the 90°curved road and other difficult tracks. Knob-type adjustable resistors plus...
Reference: RBD-2798
Add another eight pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two I2C pins which can be shared with other I2C devices, and in exchange gives you eight general purpose pins. You can set each of eight pins to be input, output, or input with a pullup. There's even the ability to get an interrupt via an external pin when any...
Reference: RBD-1155
Built-in Lipo Charging Circuit Stabilized Voltage Output High Battery Capacity
Reference: RBD-2832
Designed for use as an endstop for 3D printers but it can be used for other contact detection applications as well.
Reference: RBD-2068
Aluminum alloy mechanical arm body. Total weight 902 gram with servos and gripper. Color silver. 7 MG996R metal servo. Assembled
Reference: RBD-2833
Type: Vibration Sensors Output: Switching Transducer Dimensions: 25 x 14 x 6 (LxWxH) mm Weight: 3 gm
Reference: RBD-0404
Brand: RoboticsBD
4 DOF Robotic Arm wooden DIY unassembled Premium quality kit with wood cutting parts and screws Includes 4 SG90 servos for joint motion Untrammeled and flexible motion with 4 degrees of freedom Product's color maybe different, local material is used. If any parts got broken during setup, please email us at ask@roboticsbd.com. We may not charge you for...
Reference: RBD-2834
Enhance your 3D printer's performance with the DRV8825/A4988 Stable 42 Stepper Motor Driver Expansion Board. This expansion board offers advanced features and superior performance to meet your diverse needs in 3D printing and DIY projects.Note: Please ensure correct installation direction of the drive module to prevent module damage.
Reference: RBD-0581
Outline Size: 135 x 135 x 80mm The round acrylic plate diameter: 130mm Another acrylic plate size: 135 x 75mm
Reference: RBD-2857
Brand: DFRobot
The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and application engineers. This medium-power high-efficiency solar power management module allows you to charge a 12V lead-acid battery with a maximum of 4A using a...