Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

1 review

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-0282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

1 review

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-0576

STM8S103F3P6 ARM STM8 Minimum System Development Board Module (Arduino Compatible)

Chipboard STM32F103C8T6 On board, SWIM interface and reset button Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V. Power light and the Demo indicator light Leads all the pins and has detailed label for the Pins. Support SWIM debug mode. RoboticsBD

Reference: RBD-0439

Arduino Android IOS HM-10 BLE Bluetooth 4.0 CC2540 CC2541 Serial Wireless Module

12 reviews

Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....

Reference: RBD-1180

4 Channel 5V Relay Shield for Arduino

1 review

Standard For Shield interfaces and shape Can continue to stack other For  expansion boards 3 M3 screw positioning holes for easy installation High Drive (5V or 3.3V) normally open contact closure Onboard relay indicator (red) Note: Relay might be different from the picture as per stock

Reference: RBD-1381

Opto-Isolator ILD213T

Forward voltage 1.55V Reverse current 100mA Capacitance 25 pF

Reference: RBD-1670

ESP8285 IR Infrared Transmitter Receiver Module WIFI Remote Control Switch

The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA

Reference: RBD-1750

Instrumentation Voltage Amplifier Module AD620

2 reviews

Operating Voltage: 3- 12 VDC Amplification: Adjustable 1.5~1000 times Signal Input Voltage Range: 100µV~300mV Signal Output Range: 100µV~300mV

Reference: RBD-1753

INMP441 Omnidirectional Microphone Module

1 review

Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS

Reference: RBD-1809

Digispark Pro - ATtiny167 with Micro USB

Digispark Pro  ATtiny167  Micro USB 16MHz

Reference: RBD-0937

Mini Data Logger Module

2 reviews

SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...

Reference: RBD-2096

Eye Blink Detection Digital Sensor with Goggles

Operating Voltage: 3-5.5V Supply Current: ≥ 20mA Optimal Sensing Distance: 3mm Working voltage of 5V, the output of the black line low, white line of high output Uses Infrared Light to Detect Anti-Interference Ability Sensors to adopt TCRT5000 High Sensitivity, Stable Performance Exquisite workmanship, with the indicator Has a fixed bolt hole for easy...

Reference: RBD-2065

JQ6500 HW-896 V1.2 Voice Sound MP3 Player Module

Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts

Reference: RBD-2134

433Mhz Wireless Receiver Learning Code EV1527 Decoding Module 4Ch output With Learning Button

433Mhz Wireless Receiver Learning Code EV1527 Decoding Module 4-channel output with a learning button Compatible with Arduino/ARM/MCU Ideal for wireless power switch sockets, remote controls, LED lighting, and electric doors Wide range of applications in home automation, security systems, and remote control devices

Reference: RBD-2293

801S Vibration Sensor Analog Module

1 review

801S is a vibration sensor with a gold alloy plated shock sensor and an onboard comparator IC. The sensor is capable of providing real-time vibrational data along with micro shock detection and about 60,000,000 times shock guaranteed. Pin Type Pin Description VDD Voltage Input pin GND Ground terminal D0 Digital Signal Output pin A0...

Reference: RBD-2294

JQ6500 V2.1 MP3 Player Module

JQ6500 MP3 Voice sound module can play stereo MP3 files or standard mono audio files. The module has two different modes to operate in; serial communication mode (connecting to a microcontroller) or AD button control mode (module can be controlled with switches).

Reference: RBD-2307

Stereo Enclosed Speaker 3W 8Ω

1 review

This speaker is a great addition to any audio project where you need 8 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm...

Reference: RBD-2331

Rotary Potentiometer Analog Knobs 8 Channel Module

This is a rotary potentiometer module consisting of 8 adjustable potentiometers and the communication method is IIC interface. The module mainly uses 10K adjustable resistors. By rotating the potentiometer to change the size of the resistance value, then build a circuit to convert the change of resistance value to voltage change, read the output value...

Reference: RBD-2370

Solar/Wind energy Charging CC/CV Power Supply Module

2 reviews

Module Properties: non-isolated Buck-Boost constant current, constant voltage module (CC-CV) charging module Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Solar Panel, Wind generator voltage regulator, Car Power Supply

Reference: RBD-2409

Multifunction Shield For Arduino

10K adjustable precision potentiometer. 3 x Independent push buttons. Piezo buzzer. DS18B20 temperature sensor interface. LM35 temperature sensor interface. Infrared receiver interface.

Reference: RBD-2415

Dual PS2 Game Joystick Button Module Joystick Compatible With Arduino

Dual PS2 Game Joystick Button Module Joystick Compatible With Arduino is a module use to connect and interface PlayStation 2 (PS2) game joysticks with an Arduino microcontroller board. It provides a simple and convenient way to control various projects and applications using PS2-style joysticks. The module consists of two PS2 joysticks, each with two-axis...

Reference: RBD-2449

LM2577 Adjustable DC-DC Boost Module

Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink

Reference: RBD-2458

250W 8A Buck Converter XH-M404 Adjustable DC-DC Step-Down Module XL4016

The XH-M404 Adjustable DC-DC Step-Down Module can can step-down the input voltage to a range of 1.25 – 36V at up to 8A.

Reference: RBD-2459

5A Adjustable Step Down CC / CV Module

Converts 5 – 30V down to a 0.8 – 29V output with adjustable current limit

Reference: RBD-2460

LTC1871 Adjustable DC-DC Boost Module

LTC1871 DC-DC 3-35V To 3.5-35V Booster Step Up Module Converter Regulated Power 100W Buck-Boost Adjustable Supply LED VoltMeter

Reference: RBD-2466

1.2-34V 5A Dc-dc Step-down CC/CV Xl4015 Battery Charger Led Driver With Volt, Amp & Power Meter

This XL4015-based voltage converter is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module with Constant Voltage and Constant Current control, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation.

Reference: RBD-2475

Mechanical Decade Counters Small Size 5 Counter

5 counters with 2 end caps are bundled togeatherbezel size 1.85" x 0.94" (for 5 counters with 2 end caps) mounting hole size 1.72" x 0.875" (for 5 counters with 2 end caps) total depth (from front of button to the edge of the PCB) 1.6" single counter width 0.32"

Reference: RBD-2489

Wiznet W5500 Mini Ethernet Network Module

1 review

Wiznet Compact W5500 Network Module - 10/100 Base T WIZ850io is a compact size network module that includes a W5500 (TCP/IP hardwired chip and PHY embedded), a transformer and RJ45. It can be used as a component and no effort is required to interface W5500 and Transformer. The WIZ850io is an ideal option for users who want to develop their Internet...

Reference: RBD-2562

Open Smart Long Range 433Mhz RF Wireless Transceiver Kit For Arduino

The kit includes one pair of transmitter and receiver modules for increasing the communication distance. And the frequency is 433MHz. It is very popular for remote control systems, such as wireless doorbell, remote control rolling gates, smart car, smart home, etc.

Reference: RBD-2672

MCP3008 - Analogue to Digital Converter

MCP3008 is one of the famous Analog to Digital converter IC. This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy to use, and uses SPI so only 4 pins are required. We chose this chip as a great accompaniment to the Raspberry Pi computer, because its fun to have analog inputs but the Pi does...

Reference: RBD-2676

PWM Signal Generator Stepper Motor Speed Controller Driver Board

Suitable for use with a wide range of stepper motors and drivers. Can be integrated into a simple control platform with a stepper motor and DC power supply. Offers three selectable low-frequency signal options: high (5.4k-160kHz), middle (540-16.6kHz), and low (80-2.4kHz), adjustable via jumper settings. Capable of producing both pulse and PWM signals,...