How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0390
Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0218
High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM
Reference: RBD-1565
MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm
Reference: RBD-0323
Microcontroller ATmega328 (SMD) – Interface CH340G Operating Voltage: 5V Input Voltage (recommended): 7-12V Digital I / O Pins 14 (of which 6 provide PWM output) RoboticsBD Analog Input Pins: 6 A programming cable is included.
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-1244
Aluminum body with high torque metal gear servos 6 DOF structural design makes the robot arm move flexibly Up to 17Kg torque for joint servos Various control ways
Reference: RBD-0309
4 poles 12 slot Hi-torque motor design CNC machined 6061 T6 windings maximizes efficiency High RPM ABEC5 oversize bearings Universal fit, fit all 1/10 brushless cars-multi-mounting system for M3 screws Precision balanced rotor, smoothness for best reliability and maximum RPM
Reference: RBD-2123
STM32 chip for the main controller Easy Visual Operation Interface Support wireless handle control, smart phone APP and mouse control Provide graphical PC software and detailed tutorials The current Stock comes unassembled.
Reference: RBD-2335
The Arduino Uno R3 Standard-Quality Edition Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6 We are pleased to present a more cost-effective iteration of the Arduino Uno R3, a widely acclaimed and versatile platform for electronics...
Reference: RBD-0009
54 Digital I/O terminals (14 of which have programmable PWM outputs). 16 Analog Inputs. 4 UARTs (hardware serial ports). 16 MHz crystal clock. RoboticsBD Operating voltage: 6 ~ 12v. Dimensions: 110 x 53 x 15 mm.
Reference: RBD-0217
Model: MG90S Weight: 13 gm Operating voltage: 4.8V~ 6.6V Servo Plug: JR Stall torque @4.8V : 1.8kg-cm Stall torque @6.6V : 2.2kg-cm Note: The component, colour & shape of the motor may vary depending on our stock rotation.
Reference: RBD-0375
AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-1397
Programmer: CH340 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader
Reference: RBD-2045
Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-1214
The board is compatible with Mega 2560. excellent solution for developing projects based on ATmega2560. The board can be powered directly through the Micro USB connector The maximum output current upon 5V is around 800mA, while on the 3.3V it is about 800mA.
Reference: RBD-2251
ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38
Reference: RBD-0032
USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...
Reference: RBD-0295
Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 9.4kg-cm Stall torque @6.6V : 11kg-cm Continuous rotation servos are like regular hobby RC servos but modified to offer speed control instead of position control. They're essentially compact, affordable motors with integrated motor drivers. Add a wheel, and...
Reference: RBD-1254
Size: 202X85X200mm Weight: 1150 gram MCU: STM32F105 Motor Drive: LV8731 motor driver chip Charging Direct
Reference: RBD-0297
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0926
USB Driver: FT232 Manufacturer: Gravitech Operating Voltage (logic level): 5V 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please...
Reference: RBD-1253
Program Software: Mixly + XR Scratch(base on Scratch2.0) Input: Edge sensor, Button, IR receiver module, Ultrasonic sensor, Tracking sensor Output: Buzzer, RGBLED, Two motor port,OLED CPU: Arduino UNO R3 Power: 2Pcs 3.7V DC Lithium battery Control: WiFi control/IR remote
Reference: RBD-0432
Iron Body Material High quality ultra-compact electric lock. RoboticsBD Rustproof, durable, safe, convenient to use. Suction which tightly sucks the iron, thus locking the door. Designed with the open frame type and mount board, high power. Easy to install for the electric door lock or other automatic door lock systems with the mounting board Applicable...
Reference: RBD-1129
Brand: RoboticsBD
Complete Assembled Plug and Play Open Source Design Compatible With Arduino IDE DIY Kit
Reference: RBD-2199
Compatible with the Arduino IDE, making it easy for beginners to start using Smaller and cheaper than traditional Arduino boards Powered by a 16.0 MHz microcontroller Fully assembled except for headers, allowing for easy soldering Great for projects where size and cost are a concern Perfect for beginners to jump into electronics Can be used for a variety...
Reference: RBD-0715
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-1252
Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
