Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0346
The PN532 is a highly integrated transmission module for contactless communication at 13.56 MHz including microcontroller functionality based on an 80C51 core with 40 Kbytes of ROM and 1 Kbytes of RAM. The PN532 combines a modulation and demodulation concept completely integrated for different kinds of contactless communication methods and protocols at...
Reference: RBD-2064
TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. Note: If you want to buy the cheaper recycled SIM800L Module Click here.
Reference: RBD-1820
38 Pin version 2.4GHz Dual-Mode WiFi + Bluetooth Development Board, 38PIN Ultra-Low power consumption works perfectly with the IDE
Reference: RBD-0396
Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD
Reference: RBD-2266
Versatile and powerful development board for IoT and embedded systems projects. USB Type-C port for reversible plug orientation and easy connection to computer or other devices. Built-in Wi-Fi and Bluetooth module for wireless connectivity. Arduino IDE compatibility for easy code writing and uploading. Suitable for a wide range of applications, including...
Reference: RBD-2137
ESP32 Development Board Integrated antenna and RF balun Dual-mode Wi-Fi and Bluetooth chips Small size and high performance-price ratio Compatible with Arduino
Reference: RBD-2164
WeMos D1 R32 Mini ESP32 WIFI Bluetooth Development Board CH340 chip for compatibility with Arduino UNO R3 Supports WIFI and Bluetooth connectivity Comes with a Type-B/Micro USB adapter
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-2269
Adds WiFi and Bluetooth connectivity to your projects, great for IoT and automation applications Integrated antenna and RF balun, power amplifier, and other features in a small printed circuit board area Low power consumption and safe, reliable, and scalable RF properties Supports Lua programming and Win10 system automatic installation drive Small form...
Reference: RBD-2267
Integrated Wi-Fi and Bluetooth connectivity make this board a great choice for IoT projects and robotics. The ESP32 chip on the board is a dual-core microcontroller that operates at up to 240 MHz, providing ample processing power for complex projects. With 520 KB of SRAM and 4 MB of flash memory, the board has plenty of memory for storing and running...
Reference: RBD-0742
Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
Reference: RBD-1337
Transmission Distance(m) :400 Relay Channel:2 Trigger Voltage (VDC): 5 Switching Voltage (VAC):250@10A Switching Voltage (VDC):30@10A Baud Rate:9600 Note: Relay might be different from the picture as per stock
Reference: RBD-1529
Model:SX1278ZTR4 SX1278 433mhz module spread spectrum low power serial port module LoRa wireless module Range: 3-5 KM (line of sight) Sensitivity: down to -148dBm Programmable bit rates: up to 300kbps RSSI dynamic range: 127dB Wireless frequency: 433MHz Working voltage: 1.8-3.7v Working temperature: -40-+80 ℃
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-0914
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
Reference: RBD-1134
Easy to Assemble Comes With all Components Operating Voltage: 5VDC Operating Current: 200mA Compatible With Arduino and Raspberry Pi
Reference: RBD-0841
Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900 Connect onto any global GSM network with any 2G SIM Make and receive voice calls using an external 8Ω speaker & electret microphone Facility to connect 4-pole TRRS mic and headset
Reference: RBD-1670
The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA
Reference: RBD-1812
11 digital input/output pins Interrupt/PWM/I2C/one-wire 1 analog input(3.2V max input) 16M bytes(128M bit) Flash External antenna connector Built-in ceramic antenna New CP2104 USB-TO-UART IC
Reference: RBD-1821
Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled Arduino-like hardware IO Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLL, regulators, DCXO and power management units Onboard USB to serial chip to easily program and upload codes from the Arduino IDE Embeds logic level converter circuits...
Reference: RBD-1137
Fully Compatible with 10/100/1000Base-T Networks Integrated MAC and 10Base-T PHY Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz For Arduino, SPI,...
Reference: RBD-2131
ESP32-S2 based WIFI development board Features S2FN4R2 WIFI IC Equipped with 4MB FLASH and 2MB PSRAM Type-C USB connectivity 27 digital input/output pins with support for interrupt/pwm/I2C/single wire ADC, DAC, I2C, SPI, UART, USB OTG
Reference: RBD-1333
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)
Reference: RBD-0814
The 2021 Model is Sonoff Basic R2 Support remotely turn on or off added devices. Support Max 8 timers tasks for each added device. Works with AMAZON ALEXA Works with GOOGLE ASSISTANT Also, Work with NEST Support numerous Wi-Fi smart switches one smartphone.
Reference: RBD-1582
25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection
Reference: RBD-2488
Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet 10BaseT/100BaseTX Ethernet PHY embedded Auto-Negotiation (Full-duplex and half duplex) Support Auto MDI/MDIX Simultaneously Supports to 4 independent sockets 0.18 µm CMOS technology 3.3V operation with 5V I/O signal tolerance Provide Serial Peripheral Interface (SPI MODE...
Reference: RBD-2489
Wiznet Compact W5500 Network Module - 10/100 Base T WIZ850io is a compact size network module that includes a W5500 (TCP/IP hardwired chip and PHY embedded), a transformer and RJ45. It can be used as a component and no effort is required to interface W5500 and Transformer. The WIZ850io is an ideal option for users who want to develop their Internet...
Reference: RBD-1750
Operating Voltage: 3- 12 VDC Amplification: Adjustable 1.5~1000 times Signal Input Voltage Range: 100µV~300mV Signal Output Range: 100µV~300mV
Reference: RBD-2684
100% brand new and high quality. Widely used in street lights, neon lights, bells, radio and television equipment, production equipment, electrical equipment and household appliances automatic control. Built-in high-performance batteries as backup power in case of no electricity can still maintain time display and storage of. Auto timer error correction....
Reference: RBD-2685
Specifications: Color: White Material: ABS Dimensions: 60 x 48 x 32mm Output: 12V Power Consumption: 7.5VA Time Range: 1-168 hours Display: LCD Battery: Built-in 1.2V, 40mA Ambient Temperature: -25°C to 55°C Connection Type: Plug-in CN101A