Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0227
Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm
Reference: RBD-2045
Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included
Reference: RBD-0432
Iron Body Material High quality ultra-compact electric lock. RoboticsBD Rustproof, durable, safe, convenient to use. Suction which tightly sucks the iron, thus locking the door. Designed with the open frame type and mount board, high power. Easy to install for the electric door lock or other automatic door lock systems with the mounting board Applicable...
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-0349
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...
Reference: RBD-1762
Input voltage(V): 9-12 It can produce high-temperature PCB board size(cm): 3.1 x 4 It is convenient for fans to install high efficiency Weight(g): 20This product is shipped as unassembled and requires soldering to be completed. You will need to do the soldering yourself.
Reference: RBD-0350
100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.
Reference: RBD-0442
Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 27 x 29 x 18 mm (LxWxH) High quality ultra-compact electric lock. RoboticsBD
Reference: RBD-1809
Digispark Pro ATtiny167 Micro USB 16MHz
Reference: RBD-2112
Single side PCB. Reinforced with glass fiber laminate on the core. 250 x 380 x 1.5 mm. Ideal for prototyping. Imported from China Color: Pale Green Smooth Machine Cut
Reference: RBD-2113
Single side PCB. Reinforced with glass fiber laminate on the core. 215 x 330 x 1.4 mm. Ideal for prototyping. Color: Ash, White Smooth Machine Cut
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD
Reference: RBD-0562
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm
Reference: RBD-2131
ESP32-S2 based WIFI development board Features S2FN4R2 WIFI IC Equipped with 4MB FLASH and 2MB PSRAM Type-C USB connectivity 27 digital input/output pins with support for interrupt/pwm/I2C/single wire ADC, DAC, I2C, SPI, UART, USB OTG
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-1663
Brand: RoboticsBD
Distribution strip, Tie-point 200 Terminal Strip, Tie-point 630 Completely reusable Breadboard Brand new & high quality Breadboard power supply module, compatible with 5 V, 3.3 V 140pcs Solderless Breadboard Jumper Cable Lead Kit Hard Wire with Angled shape
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-2266
Versatile and powerful development board for IoT and embedded systems projects. USB Type-C port for reversible plug orientation and easy connection to computer or other devices. Built-in Wi-Fi and Bluetooth module for wireless connectivity. Arduino IDE compatibility for easy code writing and uploading. Suitable for a wide range of applications, including...
Reference: RBD-2662
BlackPill version 3.1 board equipped with STM32F411CEU6 microcontroller, USB type C connector, additional user programmable button, LED, built-in RTC clock, 16-channel A/D converter. It has 512 kB of Flash memory and 128 kB of SRAM memory. Popular SPI, I2C, USART and SDIO interfaces are also available. Included with the board are 2 20-pin goldpin strips...
Reference: RBD-2679
STM32F103C8T6 ARM Development Board Module with Type-C Interface and Enhanced Memory Enhance your embedded system projects with the STM32F103C8T6 ARM development board module. Featuring a Type-C interface for easy connectivity, this module offers seamless one-click download capability. With an upgraded BOOT switch, you can easily perform upgrades without...
Reference: RBD-2690
Single side PCB. Reinforced with glass fiber laminate on the core. 330 x 200 x 1.4 mm. Ideal for prototyping. Color: Copper, White Smooth Machine Cut
Reference: RBD-1215
131 powerful instructions – Most Single Clock Cycle Execution 32 x 8 general purpose working registers Fully static operation Up to 20MIPS throughput at 20MHz On-chip 2-cycle multiplier Write/erase cycles: 10,000 flash/100,000 EEPROM Optional boot code section with independent lock bits In system programming by on-chip boot program True read while write...
Reference: RBD-2831
Introducing a compatible Raspberry Pi Pico Clone, Made in China. Equipped with the authentic Raspberry Pi RP2040 microcontroller chip, this Pico offers comparable performance at a competitive price point. However, it's essential to note that while the microcontroller chip is genuine, the PCB itself is not manufactured by Raspberry Pi but rather in China....
Reference: RBD-1333
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)
Reference: RBD-1381
Forward voltage 1.55V Reverse current 100mA Capacitance 25 pF
Reference: RBD-1537
Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter: 2mm EL light length: 3M Lifetime: >12,000 hours Color: White