Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-2065
Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-1773
Supply Voltage: 5V USB / 3.7V lithium battery Output Port: 3-wire audio interface/DIY pad Output Type: Analog signal Bluetooth name: VHM-314-V3.0 Bluetooth version: 5.0 Bluetooth passcode: no password Sound source: Bluetooth. USB-PC input(after the back pad is connected, the computer can be connected as a sound card though Micro) Operation method:...
Reference: RBD-0662
Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
Reference: RBD-0353
Driver IC: SSD1306 Support wide voltage: 3.3V-5V DC Communication: IIC Working temperature: -30-80 degrees. RoboticsBD
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0981
Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-2213
Operating voltage (v):DC 8 – 24V Chipset:TPA3118 Power output:60W Material:FR4
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-2307
This speaker is a great addition to any audio project where you need 8 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm...
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-2718
Dual-Channel Stereo Output Run-on 7V to 15V power Supply 32 Steps DC volume control has a +32dB to -75dB range. 40 pin QFN 6 x 6 mm package. Much higher efficiency in terms of cost and performance than competitors’ ICs
Reference: RBD-2389
This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.
Reference: RBD-2724
The MAX4466 Electret Microphone Module is a convenient and sensitive audio sensor solution designed for capturing sound waves and converting them into electrical signals. This module incorporates the MAX4466 electret condenser microphone and an integrated amplifier circuit, making it well-suited for applications requiring clear and amplified audio capture.
Reference: RBD-2758
With this module you can easily measure sound with an analog pin on your Arduino or other microcontroller. The module has an automatic gain/amplification (ACG) of the microphone: The module amplifies sounds with a low volume more, and sounds with a higher volume less.
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-0980
Dimensions : 66 x 66 x 3 mm. Weight : 25 gm. Supply Voltage : 5 VDC. Interface : IO . 8 x 8 = 64 RGB. Chip : WS2812.
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-1065
Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate...
Reference: RBD-1098
Interface: I2C Operating Voltage: 3-5VDC Ports: 8-bit Parallel Ports Can be used with Arduino and Raspberry Pi
Reference: RBD-1164
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.