Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0267
Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0732
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch
Reference: RBD-0651
Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black.
Reference: RBD-0282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. RoboticsBD Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-0763
Cell Quantity: 2 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-0919
Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-1606
Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C
Reference: RBD-0989
Hold A standard 18650 batteries Wire : 15cm Output: 3.7v Dimension (Appro.): 76x20x20xmm Weight: 8gm High-quality plastic material
Reference: RBD-1678
2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-2209
16 channels PWM servo motor driver controller board module Supports USB interface, TTL serial port, and Bluetooth communication Bluetooth communication can connect to Android phone or PC software Master chip STM32 series, frequency 48MHz Size 43.5x36mmx12mm, operating voltage 5V USB, TTL3.3V, servo motor supply 5-7.2V Channel 16, PWM accuracy 0.1ms
Reference: RBD-2308
This Dual Dc motor driver focuses on high efficiency and can withstand high current load, the maximum current up to 30A.
Reference: RBD-1019
Charging Voltage: 12.6V-13V Overcharge Voltage Range: 4.25V-4.35V ± 0.05V Overpressure Voltage Range: 2.3V-3.0V ± 0.05V Upper Limit Operating Current: 5A-6A
Reference: RBD-2369
Built-in power switch High-performance CPU 16M high-capacity memory Built in Bluetooth 4.0 module Support TTL serial communication
Reference: RBD-2389
This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.
Reference: RBD-2390
Forward and reverse rotating :Forward and reverse rotating motor can be realized, can meet the needs of various working scenarios. Good production performance :Excellent production technology, not easy to cold joint, reliable and safe for you to use. Multiple good ability :With characteristics of strong driving ability, low heat dissipation and strong...
Reference: RBD-2419
Input Current: 0~5A Output Current: 0.5~4.0A Control Signal: 3.3~24V Power (MAX): 160W Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32 Temperature: -10~45℃ H bridge bipolar constant current drive.
Reference: RBD-1421
3S 11.1V 12.6V 20A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery). Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery). Continuous discharge current (upper limit): 20A (if the cooling environment is not good, please reduce the load current use). Continuous...
Reference: RBD-2511
Switching a lot of power? N-channel power MOSFET - 30V / 60A IRLB8721 MOSFETs are just what you need.These TO-220 package power MOSFETs can switch 30V/60A, which is plenty for most makers! They fit straight into a breadboard or even your own PCB with 2.54mm spaced pads.
Reference: RBD-2676
Suitable for use with a wide range of stepper motors and drivers. Can be integrated into a simple control platform with a stepper motor and DC power supply. Offers three selectable low-frequency signal options: high (5.4k-160kHz), middle (540-16.6kHz), and low (80-2.4kHz), adjustable via jumper settings. Capable of producing both pulse and PWM signals,...
Reference: RBD-2682
Double H bridge, which can drive two DC motors at the same time, single 7A current, high power; Wide voltage input 6.5V ~ 27V ; Signal optocoupler isolated input, can be directly controlled by IO port, free from interference; Undervoltage protection to prevent instantaneous high current burning of the module; High-power TVS and electrostatic bleeder...
Reference: RBD-2754
The L298N 4WD Motor Driver is a versatile and robust H-bridge driver module designed for controlling DC motors with ease and precision. With its compatibility with 3.3V microcontrollers and support for popular platforms like Arduino and STM32, this module offers flexibility and convenience in motor control applications.
Reference: RBD-2834
Enhance your 3D printer's performance with the DRV8825/A4988 Stable 42 Stepper Motor Driver Expansion Board. This expansion board offers advanced features and superior performance to meet your diverse needs in 3D printing and DIY projects.Note: Please ensure correct installation direction of the drive module to prevent module damage.
Reference: RBD-1334
Charging current: 1A (maximum) Maximum charging voltage: 4.2V (1.5% accuracy) Input voltage: 4.5V-5.5V
Reference: RBD-1754
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-1419
Model: 6S 15A 18650 Lithium Battery Protection Board Balanced charge: None Short circuit protection: Yes
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor