Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0280
Tie-points: 170 (10×17) Size: 48 x 35 x 10 mm(LxWxH). Use: experimental, testing, robot Matching jumper, diameter 0.8mm Phosphor bronze nickel plated spring clips Accepts a variety of wire sizes (29-20 the AWG) **1 pcs Random Color
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-1606
Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-2511
Switching a lot of power? N-channel power MOSFET - 30V / 60A IRLB8721 MOSFETs are just what you need.These TO-220 package power MOSFETs can switch 30V/60A, which is plenty for most makers! They fit straight into a breadboard or even your own PCB with 2.54mm spaced pads.
Reference: RBD-0702
It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock
Reference: RBD-2834
Enhance your 3D printer's performance with the DRV8825/A4988 Stable 42 Stepper Motor Driver Expansion Board. This expansion board offers advanced features and superior performance to meet your diverse needs in 3D printing and DIY projects.Note: Please ensure correct installation direction of the drive module to prevent module damage.
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-2177
Easy-to-use tool Small in size Color: Random Quantity: 1 pcs Weight: 0.026 kg Dimensions: 5 × 5 × 5 cm Note: You will receive random color.
Reference: RBD-2178
Mini grabber SMD IC test hook for logic analyzer Retractable hook with 2mm inner spring Perfect for continuity testing of circuit board components Can be used to test IC, repair cell phone, or other mini electronic products Double Dupont plug lead for connecting to logic analyzer or oscilloscope Note: You will receive random color. If you order 2pcs you...
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1367
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver
Reference: RBD-2453
Fully self contained panel meter with dual red and blue display.
Reference: RBD-2464
Three WiresUltra-low cost, high precision to meet most of the application requirements.low starting working voltage blue minimum 5.0V.
Reference: RBD-1398
Brand new and high quality. 1-Channel Relay interface board, Equipped with high-current relay : 15A @ 125V AC or 10A @ 250V AC Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM) **Relay Brand is different from the picture as per stock
Reference: RBD-1408
Type: CJMCU MINI USB AMS1117 MINI USB interface input 5V MINI USB outputs 5V and 3.3V DC power socket interface input 5V – 12V. DC power outlet output (5V label) 5V and 3.3V Weight: 2 gm.
Reference: RBD-1409
Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C. ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase...
Reference: RBD-1573
Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm
Reference: RBD-1738
Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH): 26 x 15 x 11 mm
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1842
Material: 12UM Stainless steel fiber Gram Weight: 0.2458g/m Strength: 2.8KGF. Length: 1m. Diameter(mm): 0.12. Resistance (Ω/m) : 27.
Reference: RBD-1911
LM358 chip onboard. 100 gain of the circuit design. 10K onboard adjustable resistance, you can adjust the magnification. Onboard power indicator. The chip has led major pin can be directly input and output signals.
Reference: RBD-1916
IC Chip: MAX3232 Operating Voltage: 3.3-5.5V It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU Pre-assembled compact size board Suitable for use with most microcontrollers Operates up to 250 kbit/s
Reference: RBD-2041
Model : KY-040. Type : Incremental Encoder. Cycles per revolution (CPR) : 20. Working voltage : 0 – 5V. Material : PCB + Brass. Mounting Nut Thread diameter: 6.6mm Weight : 10 gm.
Reference: RBD-2076
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:5mm Color: Red + Green Beam Angle:150
Reference: RBD-2077
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:3mm Wavelength:571nm + 644nm Beam Angle:150
Reference: RBD-2078
No direction, any angle can trigger the work. Sensitivity switches can be selected for the trigger sensitivity according to circuit requirements. This switch is suitable for the trigger of the small current circuit. Component Type: SW-18015P Maximum voltage: 12V Rated Heating Current: 20mA
Reference: RBD-2080
Clean, good waveform driving ability, more than 15mA. Working voltage 3.3V-5 Output format: digital switching output (0 and 1) A fixed bolt holes for easy installation