Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
Reference: RBD-0420
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. RoboticsBD Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 60mA
Reference: RBD-0949
Operating Voltage : 2.5 ~ 4V Operating Current : 130 ~ 220mA Flow Rate : 80 ~ 120 L/H Maximum Lift : 40 ~ 110 mm Outlet Outside Diameter: 7.5 mm Outlet Inside Diameter: 5 mm
Reference: RBD-1061
Low density: lightweight, low inertia. Capability to absorb shock and vibration as a result of elastic compliance. Ability to operate with minimum or no lubrication, due to inherent lubricity. The relatively low coefficient of friction. Operating Voltage(VDC): 3~12 Shaft Length (mm): 8.5 Shaft Diameter (mm): 5.5 (Double D-type) No Load Current: 40-180mA....
Reference: RBD-2182
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below.
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-1249
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 90mA
Reference: RBD-1060
Perfectly fit on the extruder Noiseless Performance Very low Current consumption Easy to install and connect.
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-0376
Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-2042
Model: LilyPad Color: Purple Material: CCL Dimensions: 30 x 30 x 6 (LxWxH) mm. Weight: 3 gm.
Reference: RBD-2184
Operating Voltage: 3 to 9VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 5mm (approx.) Weight; 30g (approx.) 1 pcs 3v-9v Short Shaft 180 DC motor
Reference: RBD-2185
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm front and rear(approx.) Weight; 19g (approx.)
Reference: RBD-2186
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm (approx.) Weight; 17g (approx.)
Reference: RBD-0152
Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation
Reference: RBD-2188
Operating Voltage: 5 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 7 mm (approx.) Weight; 30g (approx.)
Reference: RBD-2189
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) O-Shape Shaft Size 10 x 5mm/ (approx.) Weight; 19g (approx.)
Reference: RBD-2190
Operating Voltage: 1.5 to 3VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 5mm (approx.) Weight; 22.5g (approx.)
Reference: RBD-2197
Model: 030-2927Motor size : 18.6mm*15.4mm*11.8mm (approx.)Motor shaft diameter: 1.5mm (approx.)Output shaft length: 8.5mm (approx.)
Reference: RBD-2450
Micro size servo is perfect for driving micro-robot drive wheels. Continuous rotation servos are like regular hobby RC servos but modified to offer speed control instead of position control. They're essentially compact, affordable motors with integrated motor drivers. Add a wheel, and you've got a simple drive system for your robot, controllable...
Reference: RBD-2519
Small 1.5 – 3V DC motor with fan for science projects or general experimenting 3V DC motor with cable Soft 3-leaf fan bladeThe Jumper may become detached during shipping and require soldering with a soldering iron.
Reference: RBD-0621
Connects Your Arduino Nano: Provides essential connection between your Arduino Nano and a computer for programming and power. Standard Compatibility: Features USB Type-A and Mini-B connectors for universal computer connectivity. Reliable Performance: Solid workmanship and high-quality materials ensure dependable data transfer. Flexible Design: 1-meter...
Reference: RBD-0604
Effortless Connection: Connects 6mm motor shafts to Mecanum wheels for hassle-free assembly of your robotic projects. Durable Construction: Made from ABS plastic for long-lasting performance and reliability. Tool-Free Installation: Features a convenient top hole for easy attachment without requiring additional tools. Versatile Applications: Suitable for...
Reference: RBD-0145
Dual output mode, analog output more accurate A fixed bolt hole for easy installation With power indicator (red) and digital switching output indicator (green) Having LM393 comparator chip, stable. Operating Voltage: 3.3V~5V
Reference: RBD-0652
Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. RoboticsBD
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-2805
This is a miniature-size exhaust cooling fan. This fan is as small as your palm. Its working voltage is 5V DC. It can work with a simple 5V battery without any difficulty. This mini fan has the ability to run at a speed of 6800 rpm. The body of the fan is built from a combination of resin and plastic material. The combination provides strength and...
Reference: RBD-2859
Small metal vibrating motor powered by 3 V. Idle current 90 mA. Dimensions: 9 x 5.2 x 5.2 mm.