Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-0152
Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation
Reference: RBD-1061
Low density: lightweight, low inertia. Capability to absorb shock and vibration as a result of elastic compliance. Ability to operate with minimum or no lubrication, due to inherent lubricity. The relatively low coefficient of friction. Operating Voltage(VDC): 3~12 Shaft Length (mm): 8.5 Shaft Diameter (mm): 5.5 (Double D-type) No Load Current: 40-180mA....
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0427
Working voltage: 3.3V-5V Output form: digital output (0 and 1)
Reference: RBD-2186
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm (approx.) Weight; 17g (approx.)
Reference: RBD-2188
Operating Voltage: 5 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 7 mm (approx.) Weight; 30g (approx.)
Reference: RBD-2189
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) O-Shape Shaft Size 10 x 5mm/ (approx.) Weight; 19g (approx.)
Reference: RBD-0663
Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD
Reference: RBD-0665
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity. RoboticsBD Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-0683
Operating voltage: DC3-5V Operating current: less than 20mA Sensor Type: Analog Detection Area: 40mmx16mm Operating temperature: 10℃-30℃ Humidity: 10% -90% non-condensing
Reference: RBD-0685
Detection distance: 2 ~ 30cm Detection angle: 35 ° Comparator chip: LM393 3mm screw holes for easy mounting
Reference: RBD-0823
LDR module 4 PIN Operating voltage 3.3V-5V Signal output indicator light. LDR module 4 PIN Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)
Reference: RBD-1195
Temperature Coefficient Type: NTC Thermal Time Constant: 10s Resistance 10kΩ Tolerance: ±1%
Reference: RBD-1199
Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimumperformance Robust ESD performance
Reference: RBD-1209
Package type: leaded Package form: top view Radiant sensitive area (in mm2): 7.5 High photo sensitivity High radiant sensitivity Suitable for visible and near infrared radiation Fast response times Angle of half sensitivity: phi = ± 65°
Reference: RBD-1738
Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH): 26 x 15 x 11 mm
Reference: RBD-1740
Operating voltage: 3.3 to 5VDC Ball Rolling type of tilt sensor. This small module is easy to use. A fixed bolt hole for easy installation Wide voltage LM393 comparator
Reference: RBD-2059
LDR 20 mm Light Depending Resistor Low-cost sensor device Wide spectral response Use in fire alarms, smoke alarms, control street light Low cost. Ambient Temperature Range. Wide spectral response.
Reference: RBD-2072
Operating Voltage: 3.3V-5V Features wide range voltage comparator LM393 Adjustable sensitivity Signal output indicator with the retaining bolt hole, convenient installation Output form digital switch output (0 and 1 high and low level) The output effective signal is low level When there is sound, outputs low level and the signal light
Reference: RBD-2073
Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.
Reference: RBD-2079
This is 38KHz Infrared IR transmitter sensor module For Arduino Transmit 38KHz modulating signal Suitable for Arduino DIY project Material: PCB
Reference: RBD-2082
Dimension: 2.5 x 1.5 x 1.5 cm. Receiving angle: 90 °. Working voltage: 2.7 ~ 5.5V. Frequency: 37.9KHz Receiving range: 18m. Weight: 4 gm.
Reference: RBD-2083
Operating Voltage : 5v. Temperature measurement range : -55°C to 125°C. Measurement Accuracy : ±0.5°C.
Reference: RBD-2085
Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH): 26 x 15 x 11 mm
Reference: RBD-2087
Voltage 5V Photo interruption module triggers a signal when light is blocked between the opening of the sensor.
Reference: RBD-2088
Operating Voltage: 5v DC. This module is Small and Simple to use. Digital switch output (0 & 1) High sensitivity Completes the circuit when the module is tilted LED lights up when tilt switch is activated
Reference: RBD-2089
Consists of a mercury switch 680Ω resistor LED that will light up when tilt is detected.