Reference: RBD-0439

Arduino Android IOS HM-10 BLE Bluetooth 4.0 CC2540 CC2541 Serial Wireless Module

12 reviews

Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....

Reference: RBD-1057

KOOCU V501 Constant Temperature Electric Soldering Iron 25W

4 reviews

Low current leakage Light Weight and Offers good grip General purpose for all electronic applications. Advanced Heating element High-Quality Nickel-Copper plated Bit Quickly attains the working temperature Constant Tip temperature

Reference: RBD-1081

Brand: Raspberry Pi Official

Raspberry Pi 5 Active Cooler

Original Raspberry Pi Product. Temperature-Controlled Fan, Delivers up to 1.4CFM of Air Flow. Comes With Aluminium Heat Sink Compatible With the Official Raspberry Pi 5 Case. Stock is available with Complete Set. Please purchase Raspberry Pi 5 Complete Set. 

Reference: RBD-0440

HC-12 433Mhz Wireless Serial Transceiver Module - 1 Kilometer

1 review

433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD

Reference: RBD-0560

MAX485 RS-485 Module TTL to RS-485 module for Arduino

5 reviews

On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...

Reference: RBD-0282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

1 review

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-0691

IR Infrared Remote Decoder Encoding Transmitter & Receiver Wireless Module

2 reviews

Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters 

Reference: RBD-0729

GPS Antenna 1575.42 MHz

9 reviews

Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male

Reference: RBD-1233

Heat Resistant BGA Soldering Station Pad

4 reviews

High-Quality Silicone Material Anti Static Material Magnetic slots to hold a small part Bright Colour for easy view of small components

Reference: RBD-0741

433MHz 100 Meters ASK Wireless Module Kit RF

1 review

Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards

Reference: RBD-0797

U-Blox NEO-6M GPS Module

37 reviews

5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...

Reference: RBD-1322

KOOCU V900 Precision Soldering Iron

15 reviews

Brand Name: KOOCU Model: V900 soldering iron Output Temperature: 200-480 degree Celsius Output Power:25W

Reference: RBD-1378

A4 PVC Double-sided Grid Lines Cutting Board Mat Cutting Pad DIY

7 reviews

Brand new Material: PP Color: Blue  Size: approx. 300*220mm

Reference: RBD-1039

SIM800L Mini GPRS GSM Module

40 reviews

The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...

Reference: RBD-1165

Raspberry Pi 4 Acrylic Shell Case

5 reviews

9 Layer Acrylic stylish case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel

Reference: RBD-0347

Transparent Acrylic Shell Case for Raspberry Pi 3 Model B/B+

11 reviews

9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.

Reference: RBD-1533

Steel L-Bracket for NEMA 23 Stepper Motors

Motor Type: NEMA23 Material: Mild Steel(MS). Dimensions: 50x62x64 (LxWxH) mm Mounting Holes Size: 5mm Weight: 90gm.

Reference: RBD-1234

Raspberry Pi 4 Case – Red/White

2 reviews

Easy two-piece installation design Hole for mounting the pi inside the case Rubber pad grip at the bottom Precise access to all port and status LEDs with Symbols Raspberry LOGO on Top

Reference: RBD-1579

650nm 5mW Focusable Red Line Laser Module Laser Generator Diode

1 review

Laser Output Type: Red LINE Laser Weight: 15 gm. Wavelength: 650nm Voltage: 3~6V Output Power: Min 2.5mW, Typical 3.0mW, Max 5.0mW Working current: Min 10mA, Typical 20mA, Max 25mA Working voltage: Min 2.3VDC, Typical 4.5VDC, Max 8.0VDC

Reference: RBD-1580

650nm 5mW Focusable Red Cross Line Laser Module Laser Generator Diode

Laser Output Type: Red CROSS-LINE Laser Dimensions: Diameter: 12mm, Lenght: 35mm. Weight: 15 gm. Wavelength: 650nm. Voltage: 3~6V. Output Power: Min 2.5mW, Typical 3.0mW, Max 5.0mW. Working current: Min 10mA, Typical 20mA, Max 25mA. Focus point Intensity can be adjusted with help of lens ring head.

Reference: RBD-1583

RGB Multicolor Lighting LED 16.4Ft(5M)

Light Source Type: LED Indoor/Outdoor Usage: Outdoor Color: Rgb (Red, Green, Blue) Material: Copper Number of Light Sources: 300 Voltage: 12 Volts Wattage: 48.00 Water Resistance Level: Waterproof

Reference: RBD-1690

Raspberry Pi 4 Power Supply 5V 3A USB Type C

5 reviews

ON/OFF switch button on the power adapter.  Very convenient for use. 5V 3A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4

Reference: RBD-1309

Raspberry Pi Power Adapter with Switch Micro USB

11 reviews

Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin EU type. Output Plug: Micro USB Plug. Compatible with: Raspberry Pi B+, 2, 2B, 2B+,3 ,3B+, Zero, Zero W. It has a switch so you can easily power off the device without having to unplug it right from the socket.

Reference: RBD-0110

Raspberry Pi Power Adapter Micro USB

13 reviews

রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক।  আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা  5V,3A. আমরা আমাদের টেস্ট এ  5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন।  এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...

Reference: RBD-1702

Raspberry Pi 4 Power Adapter Type C

1 review

Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4

Reference: RBD-1144

5V 3A Power Supply Adapter Charger C-Type

15 reviews

Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin Type A Japan Output Plug: Type C

Reference: RBD-1578

DT-06 TTL to WIFI Module

Support serial AT command Support re-programmable, OTA firmware update Seamless transparent transmission between serial and WiFi Built-in HTTP Web Server, support configure parameters by web page

Reference: RBD-1598

Koptan 50mm x 33m High Temperature Resistant Tape for PCB & 3D Printers

Material: Polyimide Spindle Type: Roll Tape Length: 33m TapeWidth: 50mm Colour: Metallic Brown Temperature Range: 200ºC

Reference: RBD-1145

Micro HDMI Male to HDMI Male Cable for Pi 4 or 5

120 reviews

Version 1.4 HDMI to micro HDMI cable Supports 480i ,480p, 720p, 1080i, 1080p, 1440p resolution Cable Length: 1.5m Color: Black Application: Mulitimedia

Reference: RBD-1670

ESP8285 IR Infrared Transmitter Receiver Module WIFI Remote Control Switch

The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA

Reference: RBD-1773

VHM-314 V3.0 Bluetooth Audio Receiver Board

2 reviews

Supply Voltage: 5V USB / 3.7V lithium battery Output Port: 3-wire audio interface/DIY pad Output Type: Analog signal Bluetooth name: VHM-314-V3.0 Bluetooth version: 5.0 Bluetooth passcode: no password Sound source: Bluetooth. USB-PC input(after the back pad is connected, the computer can be connected as a sound card though Micro) Operation method:...