Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1101
Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB
Reference: RBD-0040
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-1700
Brand: Waveshare
Mini ST-LINK/V2 Small single board Extreme low cost solution In-circuit debugger/programmer STM8 STM32.
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-2142
Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.
Reference: RBD-0103
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications. Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch...
Reference: RBD-0150
Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~+40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser
Reference: RBD-0720
Temperature detection of the two-dimensional area: 8 × 8 (64 pixels). Digital output (capability of temperature value output). Compact SMD package (adaptively to reflow mounting). RoHS compliant. RoboticsBD
Reference: RBD-0267
Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0288
Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v
Reference: RBD-2178
Mini grabber SMD IC test hook for logic analyzer Retractable hook with 2mm inner spring Perfect for continuity testing of circuit board components Can be used to test IC, repair cell phone, or other mini electronic products Double Dupont plug lead for connecting to logic analyzer or oscilloscope Note: You will receive random color. If you order 2pcs you...
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-2181
Professional insulated quick test hook clip High voltage flexible testing probe Comes with a 4mm socket Red and black color Compact and lightweight design
Reference: RBD-2207
2 sine wave and 2 square wave output. AD9850: 0-40MHz. After the 20-30MHz frequency harmonics increases, the waveform will be less and less clean. Low-pass filter with 70MHz, so the waveform better than SN. Parallel and serial data input can be selected via a jumper.
Reference: RBD-0307
Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD
Reference: RBD-2228
Working voltage: 2.3V-5.5V. Working temperature range: -40 ~ + 105. Onboard 25MHZ (accuracy of 50ppm) active crystal. On-board high-speed amplifiers
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0349
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD
Reference: RBD-0354
Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD
Reference: RBD-0368
Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ) Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C Lifespan: >1million times Hysteresis: +10%,(RF+ -RF-)/FR+,1000g...
Reference: RBD-0382
3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD
Reference: RBD-0385
IC Name: MCP23017 Package/Case: DIP-28
Reference: RBD-0402
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-0439
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0651
Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black.
Reference: RBD-0653
Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)