Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0022
Affordable Price Operating Voltage: 5 V Sonar Sensing Range: 2-400 cm Max. Sensing Range: 450 cm Frequency: 40 kHz RoboticsBD
Reference: RBD-0378
Model: Eachine 1000TVL 1/3 CCD Lux: 0.08Lux/ F1.2 Sensor: 1/3 “CCD Format: NTSC/PAL(Free switch) Resolution: a.Ultra High Definition 1000TVL b.PAL: 976H X 582V c.NTSC: 976H X 494V Lens: 2.8mm IR coated. RoboticsBD FOV: 110 °
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-1103
Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc....
Reference: RBD-0307
Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD
Reference: RBD-0147
Adjustable Sensitivity, External GND. Detect Ambient Humidity. Provided with Fixed Bolt Hole, Convenient to Install. Power Indicator Light & Digital Output Indication Lamp. Using LM393 Chip for Stable Work. DO Small Digital Outputs Interface (0 & 1).
Reference: RBD-1700
Brand: Waveshare
Mini ST-LINK/V2 Small single board Extreme low cost solution In-circuit debugger/programmer STM8 STM32.
Reference: RBD-0151
Operating voltage 3.3V-12V A fixed bolt hole for easy installation Wide voltage LM393 comparator Maximum output current: 15mA Can work on low voltages
Reference: RBD-2142
Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.
Reference: RBD-0741
Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards
Reference: RBD-0312
Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM
Reference: RBD-0315
Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm. RoboticsBD
Reference: RBD-0912
Model: 8020 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Rated RPM: 39000. Wire Length: 6cm Prop. Length: 55
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD
Reference: RBD-0382
3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD
Reference: RBD-1338
Easy to Assemble High-Quality Components Brushed Quadcopter
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-1387
Memory Size: 128 Gigabyte Card Type: Micro SD Speed: up to 95MB/s Class: 10 High-speed Card can be used for both Mobile phone and Raspberry Pi
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0391
Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0416
Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output
Reference: RBD-0163
Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V Output voltage range (corresponding to 0-100%RH) DC 1-3.19V Test accuracy 5% RH
Reference: RBD-0423
Detecting range: >120 degree Analog and digital outputs On-board potentiometer and indicators 1% resistors to make this module more reliable and precise Operating Voltage: 3.3V – 9V Board Diameter: 40 mm.
Reference: RBD-0425
Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD
Reference: RBD-0431
Working temperature : -10℃ ~ 50℃ Working humidity : below saturation point Storage temperature : -20℃ ~ 80℃ RoboticsBD
Reference: RBD-0555
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A
Reference: RBD-0666
Crystal: the oscillation frequency of 455. Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000. Photo-detector and preamplifier in one package. Internal filter for PCM frequency. RoboticsBD Improved shielding against EMI. Don’t forget to add CR2025 Battery to your Cart as this remote does not come with a battery
Reference: RBD-0672
Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. RoboticsBD DO output: 0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.