Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-1000
Adjustable Voltage Regulator Power Management IC
Reference: RBD-1010
Timing from microseconds to hours A stable or monostable operation Adjustable duty cycle TTL compatible output can sink or source up to 200mA
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: RBD-0152
Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation
Reference: RBD-0222
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound
Reference: RBD-0242
Resistance: 1k Ohm Tolerance: 5% Max. Working Voltage: 250V Temperature Coefficient of Resistance: 50PPM/°C
Reference: RBD-0243
Resistance: 10k Ohm Tolerance: 5% Max. Working Voltage: 250V Temperature Coefficient of Resistance: 50PPM/°C
Reference: RBD-0247
Resistance: 330 Ohm Tolerance: 5% Max. Working Voltage: 250V Temperature Coefficient of Resistance: 50PPM/°C
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0652
Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. RoboticsBD
Reference: RBD-0653
Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)
Reference: RBD-0751
1pcs 12V DC 5pin Relay MODEL: 12VDC WEIGHT: 50.00g DIMENSIONS: 1.80cm x 1.50cm x 1.60cm
Reference: RBD-0756
Very low supply current Photo-detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-0836
Model: 14500 Type: Li-Ion Battery Mark Capacity: 850mah Nominal Voltage: 3.7v Color: Blue Weight: 17g Rechargeable Battery: Yes Note: It's a clone battery so the ampere couldn't be guaranteed.
Reference: RBD-1013
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
Reference: RBD-1025
Overload protection on the input and output No latch-up when the common mode range is exceeded Applications: Audio, Communications & Networking, Signal Processing Current Stock: 741CN
Reference: RBD-1115
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1116
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1117
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1118
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1119
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1120
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1121
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connection
Reference: RBD-1122
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1123
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.