How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-0555
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A
Reference: RBD-1709
Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm
Reference: RBD-1707
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 21.6gm
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: 0828
Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking. Choose your...
Reference: RBD-1950
Card reader MF522-MINI module uses the RC522 original chip to design the Supply Voltage 3.3V Works at a 13.56MHz frequency
Reference: RBD-1932
Rated voltage: 5 VDC. Port: Digital quantity. Fixed hole:3mm. Pitch:15mm. Drive: MOS tube high-level trigger, low-level cutoff. Compatible with UNO R3/ Mega2560.
Reference: RBD-2263
Type: Hexagonal coupling. Material: brass. Inner diameter: 8 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm
Reference: RBD-1157
Wick Width: 3 mm (+/- 2) Length: 1.5 Meter Material: Copper
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-2226
Operating Voltage: 24V DC Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick...
Reference: RBD-2311
USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-2425
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-0888
Robust chrome-plated metal pushbutton with a bright green LED ring Ideal for panels up to 1/2" thick Simple installation with a straightforward drill hole Integrated resistor for LED operation Supports 3 to 6V for LED operation Momentary pushbutton design for effortless activation Versatile wiring options for the LED
Reference: RBD-2044
Model: ESP32-CAM-MB Color: Black Chipset: CH340G Connectivity Technology: USB Note: The camera module is not included with the board.
Reference: RBD-2312
When it comes to adding colour to an electronics projects, these 4x4 NeoPixel Squares use WS2812 Addressable RGB LED’s to display up to 16777216 different colour combinations, with simple operations and built-in features to greatly enhance functionality. This makes them ideal as LED Displays for basic to intermediate Electronics projects, and despite...
Reference: RBD-1642
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-1371
Input: AC 100-240V/ 47-63HZ Output: DC 3.7V/ 500mA Termination voltage: 4.2V+-1%
Reference: RBD-0122
Designed for speed with four-wheel drive capabilities Reduce drag with two-wheel drive configuration N20 Gear Versatile Compact
Reference: RBD-1933
Length: 1M Diameter: 3 mm. Color: Black Material: PE/PVC/ABS
Reference: RBD-2445
Uses ultrasonic sound waves to detect obstacles and measure distance
Reference: RBD-2454
Power: 5V This module is compatible with 5V and 3.3V microcontrollers. Material: PCB + Electronic Components
Reference: RBD-1065
Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate...
