Single Axis Servo Bracket

Brand: SparkFun Electronics

Rover 5 Robot Platform 4 Motors 4 Encoders

Rover 5 Robot Platform 4 Motors 4 Encoders Description: If you’re looking for a base for your next robot, look no further than the Rover 5. The Rover 5 uses 4 independent motors, each with a hall-effect quadrature encoder and gearbox.

85mm Antiskid Shockproof Wheels, Smart Car Robot Tires with 37GB Motor

85mm Antiskid Shockproof Wheels, Smart Car Robot Tires with 37GA Motor Powerful High Torque DC Gear Motor 12V 100RPM 37GB (18~20 kg.cm Torque) With Wheel Coupling + Motor Mounting Bracket 

ESP8266 ESP-01 WIFI Wireless Transceiver Send Receive LWIP AP+STA M70

ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is an highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module. 

Reference: Venus GPS Sparkfun

Brand: SparkFun Electronics

Venus GPS with SMA Connector

Features: Up to 20Hz update rate -148dBm cold start sensitivity -165dBm tracking sensitivity 29 second cold start TTFF 3.5 second TTFF with AGPS 1 second hot start 2.5m accuracy Multipath detection and suppression Jamming detection and mitigation SBAS (WAAS / EGNOS) support 67mW full power navigation Works directly with active or passive antenna

Slip Ring - 6 Wire (1.5A) max 240V

Features: 6 wires Voltage: 210VDC / 240VAC Current Rating: 1.5A Operating Speed: 250RPM Compatible with data bus protocols Transfers analog and digital signals

Brand: SparkFun Electronics

XBee Pro 63mW RPSMA - Series 2B (ZigBee Mesh)

Features:   3.3V @ 295mA 250kbps Max data rate 63mW output (+17dBm) 1 mile (1600m) range RPSMA connector Fully FCC certified 6 10-bit ADC input pins 8 digital IO pins 128-bit encryption Local or over-air configuration AT or API command set External Antenna Required

X9C103S Digital Potentiometer Module for Arduino

Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S

STM32F103C8T6 ARM STM32 Minimum System Development Board Module Arduino

Description:Model: STM32F103C8T6.Core: ARM 32 Cortex-M3 CPU.Debug mode: SWD.72MHz work frequency.64K flash memory, 20K SRAM.2.0-3.6V power, I/O.Reset(POR/PDR).4-16MHz crystal.On-board Mini USB interface, you can give the board power supply and USB communication.

MLX90614 Contactless Temperature Sensor Module For Arduino

MLX90614 Contactless Temperature Sensor Module For Arduino Compatible Application: Thermal Imaging Camera, Wireless Temparature Measure. Easy to integrateFactory calibrated in wide temperature range:-40…+125°C for sensor temperature and-70…+380°C for object temperature.

Force Sensitive Resistor 0.5"

Description: This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance.

Leap Motion Controller

The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible  speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,

UART EM4100 RFID Card Reader RDM6300

Overview RDM6300 125KHz cardreader mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.

Male Pin Header Single Row (L Shaped)

Male Pin Header Single Row (L Shaped) (40 Pin Set)

5mW Adjustable Laser Dot Diode Module

5mW Adjustable Laser Dot Diode Module Features: 1. Output Power: 2-5mW2. Wavelength: 650nm3. Working Voltage: 3v - 5v4 .Laser Shape: Dot5. Working temperature: -10 C-40 C

HC-020K Double Speed Measuring Module With Speed Encoder Kit

Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line

ADS1115 16 Bit I2C 4 channel ADC Module

Robotics Arm EEZYbotARM MK1

This is a 3DPrinted robotic arm.The design intent was to make something "easy" to make robotics armIt uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it.All the pieces are 3DPrinted in PLA. This is a fully built and assembled  mini Robotics Arm with servos (4 dof)  Included:...

Reference: FPV

FPV Camera 720p FishEye Lens Wide Angle 165°

FPV Camera 720p FishEye Lens Wide Angle This Camera Can be used with this Boscam FPV 5.8Ghz AV Transmitter and Receiver for FPV Purpose

0.96" Inch Yellow and Blue I2c IIC Serial 128x64Oled LCD Module for Arduino Raspberry PI

Size: 0.96 Resolution: 128X64 Color: Blue Viewing angle: greater than 160 degrees Low power consumption: 0.04W during normal operation Support wide voltage: 3.3V-5V DC Working temperature: -30-80 degrees Volume: 27MM * 27MM * 4.1MM Driver IC: SSD1306 Communication: IIC, only two I / O ports Backlight: OLED self light, no backlight

PAM8406 5Wx2 Class D Digital Stereo Audio Power Amplifier Module Board

Operating voltage: 2.5V-5.5V, recommended 5VSpeaker Load: 2-8 OhmsInput and Output Connectors: Pins on 0.2" centersSize: 24 x 23 x 105 mm (L x W x H)Net weight: 3g

Waterproof DS18B20 Digital Thermal Probe or Sensor

This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!

3S 20A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V Cell

3S 20A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V Cell BMS Protection Board (20A, 3S) Battery Not Included

Thermal Printer Paper - 34'

Can be used with: http://store.roboticsbd.com/robotics-parts/265-thermal-printer-sparkfun-robotics-bangladesh.html Description: This is a 34' roll of thermal printing paper for use with our thermal printer. This roll is smaller than you find at most office supply stores so it fits directly into the printer without having to remove any paper from the roll.

60 RPM 12 Volt DC High Torque Gear Motor

Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).

4 Channel Relay Board Module Optocoupler LED for Arduino PiC ARM

Relay modules suitable for switching of higher voltages and perfect for use with microcontrollers including Arduino, ARM, AVR and PIC. The relays used are rated up to 10A and have NO/NC contacts. Each channel has an LED indicator to show the relay is on.Channels: 4Connects directly to a microcontrollerSwitching Capacity: 10AMaximum Voltage: 250VAC /...

FLiR Thermal Imaging Camera Dev Kit

The FLiR Dev Kit includes a breakout as well as a Lepton® longwave infrared (LWIR) imager. With this kit you will be able to be able to bring FLiR’s thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. Flir Lepton Installation Instruction 1 Flir Lepton...

Brand: DFRobot

25mW Infrared Line Laser Light

Brand: SparkFun Electronics

Lockitron Mechanical Assembly

Ultrasonic Sensor Acrylic Mounting Bracket

  Ultrasonic Sensor Acrylic Mounting Bracket Robotics Bangladesh

Reference: RBD -12092

Multi Chassis Tank Rescue Version Robot Platform

This is the Multi-Chassis Rescue Platform, an easy to assemble and use robot chassis kit. The Multi-Chassis kit provides you with everything you need to give your robot a unique tank tread platform with plenty of room for expansion to add various sensors and controllers.