Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0156
Operating Voltage: 3V-5V High-resolution conversion of light intensity to frequency. Chip pins all has drawn for standard 100. Put the needle (2.54 mm). Mil-convenient for bitmap board. Programmable color and full-scale output frequency. Communicate directly with a microcontroller. Low-profile surface mount package.
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0423
Detecting range: >120 degree Analog and digital outputs On-board potentiometer and indicators 1% resistors to make this module more reliable and precise Operating Voltage: 3.3V – 9V Board Diameter: 40 mm.
Reference: RBD-0824
Material: glass fiber Can connect 1-4 ESC. This has an T connector plug to connect a battery.
Reference: RBD-0321
New PT-100 Temperature Sensor AvailableClick Here PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃
Reference: RBD-1045
Outer Diameter: 68 mm. Supply Voltage: DC 4-7V. LED driver chip: WS2812B Communication interface: single wire communication. Send data at speeds of 800Kbps. The color of the light was highly consistent Full-color module, Full-color soft lights a lamp strip.
Reference: RBD-1767
Neodymium Magnet Shape Ring Dimension 48 mm Dia x 4.5mm Thick 7mm Hole (3.5mm)
Reference: RBD-1057
Low current leakage Light Weight and Offers good grip General purpose for all electronic applications. Advanced Heating element High-Quality Nickel-Copper plated Bit Quickly attains the working temperature Constant Tip temperature
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-0032
USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...
Reference: RBD-1602
Microcontroller: ESP8266EX Operating Voltage: 3.3V Digital I/O Pins: 11 (all I/O pins have interrupt/PWM/I2C/one-wire capability, except for D0) Analog Input Pins: 1 Flash Memory: 4MB On-Board Switching Power Supply: Input Voltage Range: 9V to 12V Output: 5V at 1A Max
Reference: RBD-0413
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...
Reference: RBD-2257
Soldering Iron Stand, Easy To Use Wear Resistant Soldering Iron Holder Soldering Iron Kit Adjustable Multifunctional Convenient To Clean Crafts for Welding Note: Doesn't include lead, soldering iron or tip cleaner.
Reference: RBD-2270
Powerful and versatile ESP32 SoC with WiFi and Bluetooth connectivity 4MB of flash memory and 520KB of SRAM for storing firmware and data Compatible with the Arduino development environment for easy programming Input/output pins for connecting to sensors, actuators, and other peripherals Can be programmed using MicroPython, a high-level programming...
Reference: RBD-2219
ESP32-IO shield Compatible with RoboticsBD ESP32 Core board Brings out all the pins of RoboticsBD ESP32 Core board 2 rows of 2.54mm pin headers for connecting other sensors Power supply circuit for RoboticsBD ESP32 Core board DC 7-12V voltage input DIP switch for controlling the power
Reference: RBD-1580
Laser Output Type: Red CROSS-LINE Laser Dimensions: Diameter: 12mm, Lenght: 35mm. Weight: 15 gm. Wavelength: 650nm. Voltage: 3~6V. Output Power: Min 2.5mW, Typical 3.0mW, Max 5.0mW. Working current: Min 10mA, Typical 20mA, Max 25mA. Focus point Intensity can be adjusted with help of lens ring head.
Reference: RBD-0876
Support Local Product. Made in Bangladesh. 2WD Robotics Blue Chassis With Motors Wheels Laser-cut acrylic chassis with two dual shaft motors Simple mechanical structure with 2 DC gear motors Flexible turning and eco-friendly chassis Stable and easy to expand Made with 2.5 mm BLUE acrylic sheet. You may find scratch marks due to handling and shipping....
Reference: RBD-0168
Compatible With Raspberry Pi Module: T Type GPIO Extension Adapter Dimensions: 72 x 59 x 13 (LxWxH) mm. Pins: 40 Shape: T-Shape
Reference: RBD-0039
Model: HY-SRF05 Voltage : DC5V Static current : less than 2mA Detection distance: 2cm-450cm High precision: up to 0.3c
Reference: RBD-2460
LTC1871 DC-DC 3-35V To 3.5-35V Booster Step Up Module Converter Regulated Power 100W Buck-Boost Adjustable Supply LED VoltMeter
Reference: RBD-2255
The Doublepow Smart Battery Charger (DP-D03) is a 4 slot charger. It has an input of AC110-240V 50/60Hz. It has output of DC 1.2V 180mA D/C DC1.2V 150mA AA/AAA DC9V 25mA 9V, making it suitable for charging 1.2V AA/AAA/C/D/9V Ni-MH/Ni-CD rechargeable batteries.
Reference: RBD-2377
Universal battery charger for AA, AAA, and 9V Ni-MH or Ni-CD batteries Can charge 2-4 AA or AAA batteries at once, or 1 or 2 9V batteries Charging current of 200mA for AA batteries and 150mA for AAA batteries LED indicators show the charging status Compact and portable design