Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0159
Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD
Reference: RBD-0562
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm
Reference: RBD-0329
Printing method: Thermal dot printing Printing speed: 50 - 80mm/s Resolution: 8 points/mm, 384 points/line Effective print width: 48mm. RoboticsBD
Reference: RBD-1173
Input Current : 100A Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Meet UL94-V0 flame retardant properties
Reference: RBD-1564
High voltage resistant terminal. Support solar charging. Support undervoltage protection. Support short circuit protection.
Reference: RBD-2289
Low cost, compact size dust sensor module Used to quantitative particle (> 1 micron) measurement Principle of particle counter Can sense the tobacco smoke and pollen, house dust Consist of light emitting diode lamp, detector, signal amplifier circuit and heater Used in applications such as the air cleaner or air purifier Users can use this sensor...
Reference: RBD-1582
25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-1971
Brand: DFRobot
Gravity Expansion Board Designed for Raspberry Pi Pico Compatible with a variety of Gravity sensors and modules. Gravity Expansion Board for Pico All pins brought out, no soldering required Additional Communication Ports: Digital IO, Analog IO, I2C, SPI, UART, GDI Note: The product not include Raspberry Pi Pico. Buy Raspberry Pi Pico here. Buy Raspberry...
Reference: RBD-2140
220V Double Bearing DC Motor Dynamo Generator Efficiency: IE 2 Voltage: DC 220V Frequency: 50Hz Power factor: 0.85
Reference: RBD-1474
This Lithium ion battery protection PCB protect single Lithium ion batteries. 20A continous current. Suitable for electric drills,motors,or aircraft models which require heavy current load.
Reference: RBD-2208
2x 18650 Lithium Battery Shield V8 Mobile Power Expansion Board Module 5V/3A 3V/1A Micro USB for Arduino ESP32 ESP8266 Output port: USB or expansion port Output parameter 5V / 3A or 3.3V / 1A. Conversion efficiency up to 95% Input port: MicroUSB