Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBD-0157

Mystery Fire Dragon 30A Brushless ESC

1 review

Model: Mystery Fire Dragon 30A. Constant Current: 30A (Max 40A < 10 sec). BEC: 5V 2A. Suitable Batteries: 2-3S LiPo. Application: BLDC Motors, Multirotor, Rc Planes etc.

Reference: RBD-0725

Emax Simon Series 30A ESC

6 reviews

Model: Emax Simon Series  Burst Current: 40A (up to 10Sec) Input Voltage(V): up to 16V Constant Current: 30A BEC: 5V /2A Suitable Batteries: 2 ~ 4S

Reference: RBD-1040

FM Radio Transmitter Module Arduino

FM 70-108MHz  Input Voltage 3v~5v

Reference: RBD-1333

Button Keypad 3x4 module (Assembled)

3 reviews

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)

Reference: RBD-0578

Robotics Claw Mechanical Gripper Clamp Kit

4 reviews

The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm

Reference: RBD-1543

HW30A 30A ESC Brushless Motor Speed Controller

Constant Current: 30A (Max 40A<10s). BEC: 5V 3A. Input Voltage: 11.1 ~ 11.7 V. Li-Po battery: 2S ~ 3S. Ni-MH 4-10 CELLS Auto Detect. Current stock is without connector

Reference: RBD-2135

433 Mhz Remote Control and Wireless Receiver Module 4Ch output With Learning Button

433 Mhz Remote Control and Wireless Receiver Module Learning Code 1527 Decoding 4 Channel Output with Learning Button DIY kit for Arduino/ARM/MCU Suitable for wireless power switches, remote control sockets, LED lights, electric doors, and more.

Reference: RBD-1603

MicroPython Board R3 ATmega328P+ESP8266, 8Mb flash, USB-TTL CH340G, Micro-USB

2 reviews

USB-TTL converter. Logic Level: 5V. Operating Supply Voltage: 5V. Digital I/O Pins: 14. Analog I/O Pins: 6.

Reference: RBD-1691

Emax SimonK Series Multirotor 30A Brushless ESC

1 review

Model: Emax SimonK Series. LiPo Battery Input: 2 ~ 3S. Continuous Current: 30A. Burst Current(10S): 40A (for 10Sec). BEC Mode: Linear. BEC Output: 1A/5V.

Reference: RBD-2335

Arduino Uno R3

17 reviews

The Arduino Uno R3 Standard-Quality Edition Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6 We are pleased to present a more cost-effective iteration of the Arduino Uno R3, a widely acclaimed and versatile platform for electronics...

Reference: RBD-1734

Dual GPIO Expander for Raspberry Pi Pico, Two Sets of Male Headers

1 review

Center female pin header for direct attaching the Raspberry Pi Pico. Extra USB connector for external power supply. Immersion Gold Process Black Base Panel, White Pinout Labels, Golden Rounded Outline, Stunning Aesthetic *Please make sure there are no pin conflicts between the modules you want to use together before connecting. Raspberry Pi Pico and...

Reference: RBD-2145

L298P Motor Driver Shield for Arduino

L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators

Reference: RBD-1973

Brand: DFRobot

IO Extender for micro:bit

Easy-to-use  Low-cost expansion board for micro:bit Leads out all IO ports of micro:bit Specially-designed port for “HuskyLens AI camera”. This board can be used to Provide stable 5V power supply for HuskyLens to make it run steadily in all modes. Silkscreens on the back clearly indicate the functions of all interfaces

Reference: RBD-2710

Eye Blink Detection Analog Sensor with Goggles High Quality

Why is an analog eyeblink sensor better than a digital eyeblink sensor? Currently, most eye blink sensors on the market are digital. they can only distinguish between the eye being fully closed or fully open, unable to detect partial blinks or quick blinks. However, the analog sensor provides waveforms. By analyzing analog values, you can detect full...

Reference: RBD-1388

Cap Conductive Slip Ring 4 Wire

1 review

A slip ring is an electromechanical device that allows the transmission of power and electrical signals from a stationary to a rotating structure. A slip ring can be used in any electromechanical system that requires rotation while transmitting power or signals. It can improve mechanical performance, simplify system operation and eliminate damage-prone...

Reference: RBD-1723

5V 2A Large Current Wireless Charger Module Wireless Power Supply Module

5 reviews

Model: XKT-412. Input Voltage: 12V. Output Voltage: 5V. Operating Current: 1.2-2 A. Receive Coil: 3mm, the receiver output 5V / 1A current Normal Use Distance: 2 ~ 10mm Operating Current: 1.2-2 A.

Reference: RBD-1331

AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

1 review

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A

Reference: RBD-1923

PWM to Voltage Converter Module 0-100% to-10V

2 reviews

Conversion range: 0% -100% PWM to 0-10v voltage PWM signal reception frequency range: 1KHz – 3KHz Operating voltage: 12V – 30V DC Allowable error: 5%

Reference: RBD-1330

AC Light Dimmer Module, 1 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

3 reviews

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A

Reference: RBD-2573

Cap Conductive Slip Ring 6 Wire

A slip ring is an electromechanical device that allows the transmission of power and electrical signals from a stationary to a rotating structure. A slip ring can be used in any electromechanical system that requires rotation while transmitting power or signals. It can improve mechanical performance, simplify system operation and eliminate damage-prone...

Reference: RBD-2114

Multifunctional Expansion Board LM35 Temperature Buzzer for UNO

Multifunctional Expansion Board LM35 Temperature Buzzer for Arduino UNO Fully compatible with Arduino UNO interface Integrates multiple module functions Provides basic experimental modules for beginners Expansion ports for additional module experiments