Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0338
Brand: Waveshare
Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F
Reference: RBD-0368
Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ) Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C Lifespan: >1million times Hysteresis: +10%,(RF+ -RF-)/FR+,1000g...
Reference: RBD-0728
Working voltage: 5.5v-35v lipo 2s-5s Continuous current: 3A Instantaneous current: Min. 4A 20 seconds Output voltage: 5.25V +/-0.5V Suitable for: RC AirPlane Multirotor helicopter Special for FPV image transmission
Reference: RBD-1104
Isp interface: 6 PIN Isp interface: 10 PIN Power supply options: USB power Power supply options: external power supply (remove jumper cap)
Reference: RBD-2256
Brand: Goot Original
Equivalent 40W Ergonomic Design Economically priced general purpose soldering iron. Compact and lightweight design for easy handling. Available with Long life tip.
Reference: RBD-1543
Constant Current: 30A (Max 40A<10s). BEC: 5V 3A. Input Voltage: 11.1 ~ 11.7 V. Li-Po battery: 2S ~ 3S. Ni-MH 4-10 CELLS Auto Detect. Current stock is without connector
Reference: RBD-1814
High-Speed USB2.0 specification at 480Mbps, compatible with USB 1.1 USB2.0 Core, high speed 8051 core, 16K RAM. Built-in IDE interface for IDE devices Powered by USB Port Compact Design
Reference: RBD-2147
The built-in 24bit AD converter. Immersion gold PCB, high quality, machine welding process to ensure quality. Power supply: 3 – 5V ( internal low dropout regulator ). Communication modes: Standard the IIC / SPI communication protocol.
Reference: RBD-2289
Low cost, compact size dust sensor module Used to quantitative particle (> 1 micron) measurement Principle of particle counter Can sense the tobacco smoke and pollen, house dust Consist of light emitting diode lamp, detector, signal amplifier circuit and heater Used in applications such as the air cleaner or air purifier Users can use this sensor...
Reference: RBD-1700
Brand: Waveshare
Mini ST-LINK/V2 Small single board Extreme low cost solution In-circuit debugger/programmer STM8 STM32.
Reference: RBD-2372
This product is an ID card decoding module. After sensing the ID card, it will actively decode and output the 10-digit card number. It also has an output port that can output high and low levels, which can meet the requirements of general ID cards, such as reading, deleting, and registering. Card operation!
Reference: RBD-2515
Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 5 Kg / 11 lb Approximate Pickup Weight: 1 Kg / 2 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through...
Reference: RBD-1582
25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection
Reference: RBD-1913
Onboard LDO Voltage regulator Can be interfaced with 3V3 or 5V Microcontroller. Tap/Double Tap Detection Free-Fall Detection Analog output Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from the motor and other high current electronics Power LED
Reference: RBD-2518
1/2" Nominal NPS Working Pressure: 0.02 Mpa - 0.8 Mpa Working Temperature: 1 ℃ - 75 ℃ Response time (open): ≤ 0.15 sec Response time (close): ≤ 0.3 sec Actuating voltage: 12VDC Actuating life: ≥ 50 million cycles
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-0841
Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900 Connect onto any global GSM network with any 2G SIM Make and receive voice calls using an external 8Ω speaker & electret microphone Facility to connect 4-pole TRRS mic and headset
Reference: RBD-1690
ON/OFF switch button on the power adapter. Very convenient for use. 5V 3A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-0939
RGB Backlight Keys Onboard trackpad with all mouse function Left+Right click Gaming keys Operate on inbuilt Rechargeable battery Navigation, Volume Rockers and Home key Portable Pocket Size Plug and Play operation, No drivers needed to install Compatible with all Devices and operating Systems
Reference: RBD-0752
Onboard trackpad with all mouse function Left+Right click Gaming keys Operate on inbuilt Rechargeable battery Navigation, Volume Rockers and Home key Portable Pocket Size Plug and Play operation, No drivers needed to install Compatible with all Devices and operating Systems. RoboticsBD
Reference: RBD-1909
6v 2800mah AA NI-MH Battery Rechargeable Battery Pack JST Plug
Reference: RBD-2137
ESP32 Development Board Integrated antenna and RF balun Dual-mode Wi-Fi and Bluetooth chips Small size and high performance-price ratio Compatible with Arduino
Reference: RBD-2710
Why is an analog eyeblink sensor better than a digital eyeblink sensor? Currently, most eye blink sensors on the market are digital. they can only distinguish between the eye being fully closed or fully open, unable to detect partial blinks or quick blinks. However, the analog sensor provides waveforms. By analyzing analog values, you can detect full...
Reference: RBD-0581
Outline Size: 135 x 135 x 80mm The round acrylic plate diameter: 130mm Another acrylic plate size: 135 x 75mm
Reference: RBD-2488
Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet 10BaseT/100BaseTX Ethernet PHY embedded Auto-Negotiation (Full-duplex and half duplex) Support Auto MDI/MDIX Simultaneously Supports to 4 independent sockets 0.18 µm CMOS technology 3.3V operation with 5V I/O signal tolerance Provide Serial Peripheral Interface (SPI MODE...
Reference: RBD-0879
Support Local Product. Made in Bangladesh. 4WD Robotics Blue Chassis With Motors & Wheels Laser-cut Gorjon Plywood chassis with four dual shaft motors Simple mechanical structure with 4 DC gear motors Flexible turning and eco-friendly chassis Stable and easy to expand Made with 3mm Gorjon PlyBoard You may find scratch marks due to handling and...
Reference: RBD-2467
0-150kHz PWM generator in a panel mount enclosure
Reference: RBD-1865
HW-633 control board Automatic power-off when full charged Intelligent, Power Saving, Safe Suitable for 12-24V Storage Battery Battery application: Lead-acid batteries, Solar cells, new energy batteries, Car battery, electric car battery, Lithium-ion battery, polymer battery Made of ABS plastic and metal, durable and tough Automatic power-off when full...
Reference: RBD-1083
Panasonic ML-2020 Battery Comes with a connector for Pi 5 board Easy to install and Replace Double-sided adhesive pad to attach it to the inside of a case Stock will be available and shipped in November 2023. Join the Waitlist to receive Stock-in update
Reference: RBD-1699
Brand: SparkFun Electronics
Simple switches Detect a collision SPST switch