
Reference: 984
Heat Shrink Tube
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 245
Choose your desire Resistor value from below:
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Features:
Reference: 1297
The CD4027 is a CMOS based high voltage high speed Dual JK Flip-Flop package. The Flip-Flop could typically operate at a speed of 16MHz even at high voltages like 15V with a low noise margin of only 2.5V.
Reference: 1275
The DS1307 is a low power Full Binary (BCD) Real Time Clock (RTC) IC with 56 bytes of SVRAM that communicates through I2C Protocol. The IC can work from directly supply on Vcc and switch to Battery automatically when required.
Reference: 1283
UM3561 UM3561A DIP-8 Si Tai&SH Hengtai IC DIP Type: Logic ICs Condition: New Supply Voltage: V Dissipation Power: W Operating Temperature: standard Model Number: UM3561 UM3561A DIP-88 is_customized: Yes Package: DIP Application: IC Unit Type: piece Package Weight: 0.01kg (0.02lb.) Package Size: 10cm x 10cm x 10cm (3.94in x 3.94in x 3.94in)
Reference: 1606
The L297 Stepper Motor Controller IC generates four phase drive signals for two phase bipolar and four phase unipolar step motors in microcontroller controlled applications.
Reference: 1294
AT89C52 – 8 bit Microcontroller Compatible with MCS-51 Products Two 16-bit Timer/Counters Eight Interrupt Sources Programmable Serial Channel Low-power Idle and Power-down Modes 40-pin DIP
Reference: 23
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low.
Reference: 840
6.5x14.5cm Stripboard Veroboard Uncut PCB Platine Single Side Circuit Board. Type: DOT If you want to purchase line type Veroboard please click here.
Reference: 1061
DC Gear Motor RPM: 180 Volt: DC 3V~6V Dual Shaft
Reference: 1349
It is another great blue backlight LCD display. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you will be able to realize data display via only 2 wires. If you already has I2C devices in...
Reference: 1153
This set of jumper wires can help you remove the clutter on your breadboard