
Reference: 984
Heat Shrink Tube
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 245
Choose your desire Resistor value from below:
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Solderless Large Breadboard
A breadboard (or protoboard) is usually a construction base for prototyping of electronics. The term "breadboard" is commonly used to refer to a solderless breadboard (plugboard).
Because the solderless breadboard for electronics does not require soldering, it is reusable. This makes it easy to use for creating temporary prototypes and experimenting with circuit design.
A breadboard (or protoboard) is usually a construction base for prototyping of electronics. The term "breadboard" is commonly used to refer to a solderless breadboard (plugboard).
Because the solderless breadboard for electronics does not require soldering, it is reusable. This makes it easy to use for creating temporary prototypes and experimenting with circuit design.
Reference: 1408
Description: AMS1117 3.3V 5V/3.3V DC Mini USB Power Supply Module 1 MINI USB input: 5V DC 2. DC power input: 5V-12V 3. Output: 5V / 3.3V 4. size: 25 * 25mm Package Include: 1x AMS1117 3.3V 5V/3.3V DC Mini USB Power Supply Module
Reference: 578
This robotic claw arm is great for all your gripping needs. They are made from Aluminium and are pretty heavy-duty. The claw opens to about 2" and depending on the servo motor used, it can pick up some relatively heavy objects. Because the arms move parallel to each other, you get a better grip. The Robot Claw does not come with a servo motor. Compatible...
Reference: 411
Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...
Reference: 419
Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...
Reference: 439
This small size Bluetooth 4.0 TTL transceiver module allows your target device communicate with. your iPhone/iPAD, IOS 6 or Android 4.3 above devices. It's easy to use and completely encapsulated. You can set it as slave or master.You can use AT command set the baudrate.
Reference: 369
Brand: SparkFun Electronics
Features: 3.3V @ 295mA 250kbps Max data rate 63mW output (+17dBm) 1 mile (1600m) range RPSMA connector Fully FCC certified 6 10-bit ADC input pins 8 digital IO pins 128-bit encryption Local or over-air configuration AT or API command set External Antenna Required
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 562
DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator Input voltage: DC 3 V to 6 VInput current: 2 A - 5 AHigh-pressure type: the type of pulse currentOutput voltage: 400000 v(Please pay attention to safety)High-pressure discharge distance between 10 mm - 20 mmThe output high voltage wire length: 100 mm
Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 233
Brand: SparkFun Electronics
Description: This is the LSM9DS0, a versatile motion-sensing system-in-a-chip that houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer. That’s right, 9 degrees of freedom (9dof) from a single IC!
Reference: 1399
This is a 12V 2-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) . **Relay Brand is different from the picture as per stock
Reference: 840
6.5x14.5cm Stripboard Veroboard Uncut PCB Platine Single Side Circuit Board. Type: DOT If you want to purchase line type Veroboard please click here.
Reference: 1573
Five-Way Navigation Button Module 5D Joystick Independent Keyboard Switch Button Single Chip
Reference: 1112
Type 1: 6DOF Robot Arm Kit with 6 PCS Servos Type 2: Robot Arm Kit with Control board, Claw, 8 PCS Servos Name: 6DOF Robot Arm Kit Type: DIY robot Degree: 6 degrees of freedom Material: Stainless steel For: 8 years old and above Size: 270*105*215mm Note: Unassembled Delivery, which required you with patience and hands-on ability. Assemble...
Reference: 196
Brand: DFRobot
INTRODUCTION The APC220 radio module provides a simple and economic solution to wireless data communications. Integrates an embedded high speed microprocessor and high performance IC that creates a transparent UART/TTL interface, and elminates any
Reference: 285
Brand: RoboticsBD
3D Printed Pan Tilt Camera Mount With Servo Motor Package Include: 1x 3D Printed Pan Tilt Bracket 2x 9g Servo Motor (Assambled with the Pan Tilt Bracket) Fully assembled 3D Printed (ABS Filament) strong Pan Tilt Camera Mount With Servo Motor 9g
Reference: 268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: 1244
http://www.lewansoul.com/product/detail-6.html# Included Controller and Arduino Nano The robotic arm is DIY kit, please refer to our 3D animation to assemble the mechanical arm by yourself. Please scan the QR code or access the link inside the package to get all the information. It’s not open resource, please ignore the label on the package.
Reference: 948
ESP32 Development Board WiFi+Bluetooth Ultra Low Power Consumption Dual Cores ESP-32 ESP-32S Board
Reference: 1400
This is a 12V 4-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) . **Relay Brand is different from the picture as per stock
Reference: 390
Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).
Reference: 1540
EL wire is a thin copper wire coated in a phosphor that glows a 360 degree unbroken light when an alternating current is applied to it. It is bendable as a thin neon tube which makes it ideal for flexible decoration. It is great for car decoration, parties, camping and so on.
Reference: 796
18 DOF Aluminium Metal Hexapod Robot Spider Six Foot/Feet Robotic Frame/Chassis Kit
Reference: 315
Features: Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm
Reference: 1388
Specification:- Voltage: 240 VAC/DC- Current: 2A per circuits- Speed: 0-300 Rpm- Circuits: 6- Housing Material: Engineering Plastics- Work Humidity: 60%RH or higher- Work Temp.: -40 Degree ~+80 Degree- Contact material: Gold plated ring-Gold plated brush- nsulation resistance: 1000
Reference: 1071
Description This is a compact mounting bracket ideally designed for N20 micro gear motors. It is made of ABS plastic material and it is designed to fit perfectly to N20 motors. The motor bracket only suitable for N series motor, such as motor N20, N20 geared motors, N20 screw motor, N30 motor. Brief Data: Height: 11mm. Width: 25mm. Material: ABS plastic....
Reference: 1541
37 IN 1 BOX Sensor Kits /37 SENSOR KIT For Arduino with Plastic Box
Reference: 289
16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685 You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output.
Reference: 1006
L7906CV Negative Voltage Regulator, 1.5A, -6V 3-Pin.
Reference: 359
(Retired) Specification: - Weight: 176g- Size: 21*32*107mm- Single rated voltage: 3.7V- Single full charged voltage: 4.2V- Battery pack rated voltage: 11.1V- Battery full charged voltage: 12.6V- Continuous discharge rate: 20C- Battery pack rated capacity: 2200mAH- Cell material: Nano li-polymer
Reference: 152
SW-420 NC Type Vibration Sensor Module Arduino
Reference: 954
Package included:1 x XTAR VC2 Charger1 x USB cable1 x Bag
Solderless Large Breadboard
A breadboard (or protoboard) is usually a construction base for prototyping of electronics. The term "breadboard" is commonly used to refer to a solderless breadboard (plugboard).
Because the solderless breadboard for electronics does not require soldering, it is reusable. This makes it easy to use for creating temporary prototypes and experimenting with circuit design.