Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0032
USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...
Reference: RBD-0320
Internal integrated cold junction compensation circuit. RoboticsBD With a simple three serial SPI interface; Temperature signal can be converted into 12-bit digital Embedded thermocouple break detection circuitry. High impedance differential inputs. Operating Voltage(VDC): 3 to 5.5 Temperature Range(°C): 0 to +1024 Cold Junction Compensation Range(°C):...
Reference: RBD-0321
New PT-100 Temperature Sensor AvailableClick Here PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃
Reference: RBD-0227
Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm
Reference: RBD-1853
Suitable for Arduino, DIY & Hobby Kits, and 5V Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
Reference: RBD-2056
Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5s
Reference: RBD-1874
Suitable for DIY & Hobby Kits, Routers, and Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
Reference: RBD-1879
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: NBSB24120200VU Brand: Motorola
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-1915
Input voltage range : 3-34V DC Output voltage range : 4-35v DC adjustable Output current:3A Voltmeter range:0 to 40V,error +-0.1v Multiple output regulator. One button to switch input and output voltage display. Power-down memory function. Press the button for 3 seconds can turn OFF/ON the LED display.
Reference: RBD-1930
Suitable for DIY & Hobby Kits, Routers, LED Strip Driver, and Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved. Note: Adapter only....
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-2677
Operating on a 5V DC power supply with a current consumption of less than 60mA, this 0.28-inch Digital Voltmeter Ammeter is a versatile tool for measuring voltage and current. With a testing range of 0-100V for voltage and 1-100A for current, this meter offers precise measurements with easy readability, even in dim light conditions.
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-2208
2x 18650 Lithium Battery Shield V8 Mobile Power Expansion Board Module 5V/3A 3V/1A Micro USB for Arduino ESP32 ESP8266 Output port: USB or expansion port Output parameter 5V / 3A or 3.3V / 1A. Conversion efficiency up to 95% Input port: MicroUSB
Reference: RBD-2804
Operating Voltage(V): 5 ~24 Current Consumption Max: 5 mA Detection distance(mm): 5 mm. Type of detection: Inductive. Cable Length: 145 cm. Response Frequency: 500Hz Max. Protection class: IP 67.
Reference: RBD-2272
Input voltage range: 6V to 40V Efficiency up to 96%, measured at 20A, converting 24V to 12V Designed with 75V/80A large current dual MOS tube Uses high frequency low resistance electrolytic capacitor for stable output Convenient wiring with large current 30A screw terminals
Reference: RBD-2355
The Type-C 3A High Power 9V 18650 Lithium Battery Boost Charging Module is designed for non-power failure applications where seamless power supply switching is required. It allows for external power supply usage when available and automatically switches to battery power during power outages. When utilizing the USB interface for power supply, it is...
Reference: RBD-2806
K Type Thermocouple Temperature Sensor 100mm Probe 0‑400℃
Reference: RBD-0349
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...
Reference: RBD-2356
The Type-C 3A High Power 12V 18650 Lithium Battery Boost Charging Module is designed for non-power failure applications where seamless power supply switching is required. It allows for external power supply usage when available and automatically switches to battery power during power outages. When utilizing the USB interface for power supply, it is...
Reference: RBD-2845
Waterproof analogue sensor with the high temperature working in the range from -200°C to 420°C. The output is resistance dependent on temperature. Probe length is 200 mm.
Reference: RBD-0350
100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.
Reference: RBD-2940
The MOSFET F5305S 4-Channel Pulse Trigger Switch Controller is a versatile and robust module designed for controlling high-power devices through PWM input. This controller is perfect for managing the speed of motors, adjusting the brightness of light bulbs, and other applications requiring precise control. Based on the reliable F5305S MOSFET model, this...
Reference: RBD-2370
Module Properties: non-isolated Buck-Boost constant current, constant voltage module (CC-CV) charging module Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Solar Panel, Wind generator voltage regulator, Car Power Supply
Reference: RBD-0354
Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD
Reference: RBD-2449
Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink
Reference: RBD-2458
The XH-M404 Adjustable DC-DC Step-Down Module can can step-down the input voltage to a range of 1.25 – 36V at up to 8A.
Reference: RBD-2459
Converts 5 – 30V down to a 0.8 – 29V output with adjustable current limit
Reference: RBD-2460
LTC1871 DC-DC 3-35V To 3.5-35V Booster Step Up Module Converter Regulated Power 100W Buck-Boost Adjustable Supply LED VoltMeter
Reference: RBD-2466
This XL4015-based voltage converter is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module with Constant Voltage and Constant Current control, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation.