Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-2412
Compatible Chips:ATMega Series Tiny Series Classic Series CAN Series PWM Series You can also use this to recover your Arduino Bootloader
Reference: RBD-2413
Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...
Reference: RBD-0349
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...
Reference: RBD-2416
5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver
Reference: RBD-2425
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-0364
Reduces the risk of hardware failure due to overheating Low profile, will fit into most cases. Simple, Passive cooling. No need for noisy fans. RoboticsBD Perfectly sized for the RPi’s CPU
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-2427
Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.
Reference: RBD-2463
The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V
Reference: RBD-2655
5V power supplied by a USB connector USB 2.0 full speed compatible interface USB standard A to mini B cable 1.65V to 5.5V application voltage supported on SWIM interface SWIM low speed and high-speed modes supported Made in China To upgrade the programmer using STM32CubeProgrammer you need to enable the "Shared" options. This product is a clone and might...
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-2714
The ST-LINK V2.1 emulator offers comprehensive support for all STM32 models, providing versatile functionality for development and debugging tasks. This product is a clone and might not support STM32Cube.
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. RoboticsBD Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-2746
QL-2006 programmer is the high-speed programmer designed specially for development and production programming of PIC single chip microcomputer (SCM) by QLS Electronic Technology Co., Ltd. The product is featured with small volume, low power consumption, high reliability as well as easy and convenient operation.QL-2006 is applicable for almost all...
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0402
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-0336
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 54 Torque: 40KG.CM
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0422
Dimensions: 210 x 17 mm(LxW) Weight: 8 gm. Fit for Fingerprint Scanner - TTL (GT-511C3) & Fingerprint Scanner - 5V TTL (GT-511C1R) Wire Sleeve material: Silicon. RoboticsBD
Reference: RBD-0668
Crystal 32.768KHz, matching capacitance 6pF DS1302 8-pin SMD homemade chips Seconds, Minutes, Hours, Day of Month, Day of Week, and Year Operating temperature: 0 degree — 70 degree. RoboticsBD
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-0732
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch
Reference: RBD-1932
Rated voltage: 5 VDC. Port: Digital quantity. Fixed hole:3mm. Pitch:15mm. Drive: MOS tube high-level trigger, low-level cutoff. Compatible with UNO R3/ Mega2560.
Reference: RBD-0753
Input Voltage(Max.) : 5V Resistance: 90 Ω Resonance Frequency: 2048 Hz Sound pressure(dB(A)/10cm)min.: 80 Body Size : 12 x 9.5mm Pin Pitch: 6mm External Material: Plastic; Color: Black
Reference: RBD-0754
Plug Type: 5.5 x 2.1mm Pin: 3 Temperature: -30°C ~ +70°C. Rated load: up to DC 30V / 1.0A. Contact resistance: ≤0.03. Insulation resistance: ≥100 MΩ.
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0756
Very low supply current Photo-detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light