Reference: RBD-0660

Power Distribution Board

1 review

Material: glass fiber Can connect 1-4 ESC. RoboticsBD This has an XT60 plug to connect a battery.

Reference: RBD-2438

Brand: Raspberry Pi Official

Raspberry Pi 5 4GB

Model: Raspberry Pi 5 Model 4GB Ram: LPDDR4X-4267 4GB  SDRAM PCIe 2.0 x1 interface for fast peripherals 5V/5A DC power (PD enabled) Real-Time Clock (RTC), powered by an external battery On-board power button!! Stock is available with Total Set. Please purchase Raspberry Pi 5 Complete Set. 

Reference: RBD-0260

Jumper Wire housing 5 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0319

K Type Thermocouple Sensor Probe for Temperature Controller

2 reviews

Type K Type.  Mounting thread: M6  Temperature Range:0-600°C. RoboticsBD

Reference: RBD-0704

CC3D Flight Controller OpenPilot STM32 32-bit Flexiport

2 reviews

3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...

Reference: RBD-1081

Brand: Raspberry Pi Official

Raspberry Pi 5 Active Cooler

Original Raspberry Pi Product. Temperature-Controlled Fan, Delivers up to 1.4CFM of Air Flow. Comes With Aluminium Heat Sink Compatible With the Official Raspberry Pi 5 Case. Stock is available with Complete Set. Please purchase Raspberry Pi 5 Complete Set. 

Reference: RBD-0262

Jumper Wire housing 6 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0383

ADS1115 16-Bit ADC- 4 Channel with Programmable Gain Amplifier

2 reviews

Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference

Reference: RBD-0718

FlySky FS-CT6B 2.4GHz 6CH Transmitter With Receiver FS-R6B Mode 2

2 reviews

Model Type: Digital Radio Transceiver. Sensitivity: 1024. Bandwidth: 500 kHz. Default Operating Mode: Mode 2 (Left-Hand Throttle). No. of Channels: 6. Operating Voltage: 12V DC (1.5AA x 8 Battery) (not included).

Reference: RBD-0872

Brand: Raspberry Pi Official

Raspberry Pi Zero 2 W

1 review

Raspberry Pi Zero 2 W: Your Incredibly Tiny Mini Compute The marvel of compact engineering, packing impressive power into an unbelievably small form factor. Ideal for DIY enthusiasts, hobbyists, and professionals alike, this mini-computer opens up a world of possibilities. Whether you're building smart home devices, creating IoT projects, or exploring...

Reference: RBD-0263

Jumper Wire housing 7 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

14 reviews

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-0719

FlySky FS-i6 2.4G 6CH AFHDS RC Transmitter With FS-iA6 Receiver

8 reviews

Bandwidth (KHz): 500. RF Range (GHz): 2.40 ~ 2.48. No. of channels: 6. Remote controller weight (gm): 400. Power: 6V (1.5V AA*4). Antenna Length: 26mm * 2 (dual antenna). Transmitting Power: ≤ 20dBm. RF Receiver Sensitivity: -105dbm. RoboticsBD

Reference: RBD-0740

Brand: Raspberry Pi Official

Raspberry Pi Zero W

10 reviews

Fully HAT compatible 40pin GPIO (Unpopulated) Stream and watch Hi-definition video output at 1080P 512MB RAM and Micro SD Slot for OS Tiny Current Draw ~ 140mA at 5V! Mini-HDMI for Video Micro-USB OTG Host for Data and Power Micro-CSI Camera Port On-Board Bluetooth and WiFi. RoboticsBD

Reference: RBD-0269

Jumper Wire housing 8 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0396

Ultrasonic Transducer Waterproof Distance Measuring Sensor Module

10 reviews

Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD

Reference: RBD-0725

Emax Simon Series 30A ESC

6 reviews

Model: Emax Simon Series  Burst Current: 40A (up to 10Sec) Input Voltage(V): up to 16V Constant Current: 30A BEC: 5V /2A Suitable Batteries: 2 ~ 4S

Reference: RBD-2393

Brand: Raspberry Pi Official

Raspberry Pi Pico W with Soldered Headers

2 reviews

The Raspberry Pi Pico W builds upon the great cost-for-performance metrics of the Pico and add WiFi to the board. The Pico W features the same attributes as the Raspberry Pi Pico and also incorporates an Infineon CYW43439 wireless chip. CYW43439 supports IEEE 802.11 b/g/n wireless LAN, and Bluetooth® 5.2. (6/30/2022: Only Wireless LAN is supported on the...

Reference: RBD-0706

UNI-T A12T Temperature Humidity Meter

1 review

Dual temperature measurement. RoboticsBD Clock function: 12/24 hour modes  Alarm clock: Rings up to 60s   Comfort level: comfortable, wet, dry

Reference: RBD-0728

Hobbywing 3A UBEC 5V

2 reviews

Working voltage: 5.5v-35v lipo 2s-5s Continuous current: 3A Instantaneous current: Min. 4A 20 seconds Output voltage: 5.25V +/-0.5V Suitable for: RC AirPlane Multirotor helicopter Special for FPV image transmission

Reference: RBD-2386

Brand: Raspberry Pi Official

Raspberry Pi Pico W

1 review

The Raspberry Pi Pico W builds upon the great cost-for-performance metrics of the Pico and add WiFi to the board. The Pico W features the same attributes as the Raspberry Pi Pico and also incorporates an Infineon CYW43439 wireless chip. CYW43439 supports IEEE 802.11 b/g/n wireless LAN, and Bluetooth® 5.2. (6/30/2022: Only Wireless LAN is supported on the...

Reference: RBD-0709

UNI-T UT890D+ Digital Multimeter

1 review

6000 Counts True RMS voltage and current measurements Capacitance, Resistance, Buzzer, Diode

Reference: RBD-0729

GPS Antenna 1575.42 MHz

9 reviews

Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male

Reference: RBD-1599

Brand: Raspberry Pi Official

Raspberry Pi Pico

11 reviews

RP2040 microcontroller chip designed by Raspberry Pi Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz 264KB of SRAM, and 2MB of onboard Flash memory 26 × multi-function GPIO pins 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels Temperature sensor

Reference: RBD-1681

Jumper Wire housing 4Pin

1 review

3D printed Dupont connector for Jumper cable 4pin

Reference: RBD-0711

UNI-T UT61A Digital Multimeter

Auto range MAX/MIN/REL mode Auto power off LCD backlight Analog bar graph

Reference: RBD-0735

Pixhawk PX4 2.4.8 Drone Flight Controller Autopilot Kit

2 reviews

Supply Voltage: 7V.Processor: 32 Bit Cortex M4 CoreBus interface (UART, I2C, SPI, CAN).Firmware: Mission planner.Sensors: Gyrometer, Accelerometer, Barometer & MagnetometerMicro SD card to record flight data. RoboticsBD

Reference: RBD-2012

Brand: Raspberry Pi Official

Raspberry Pi Pico With Soldered Headers

4 reviews

RP2040 microcontroller chip designed by Raspberry Pi Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz 264KB of SRAM, and 2MB of onboard Flash memory 26 × multi-function GPIO pins 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels Onboard temperature sensor

Reference: RBD-2182

3D Printer Nozzle M7 Thread Brass 1.75mm

Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below. 

Reference: RBD-0712

UNI-T Scope Digital Multimeter UT81B

Signal input data processing auto measure  waveform storage and transfer AC/DC voltage and current resistance diode continuity frequency duty ratio capacitance

Reference: RBD-0736

7x20mm Coreless Motor with 55mm Propeller Pair

9 reviews

Model: 720 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Current: 0.1 A. Rated RPM: 48000. Max Speed: 50000 RPM. Wire Length: 5cm Prop. Length: 55mm

Reference: RBD-1734

Dual GPIO Expander for Raspberry Pi Pico, Two Sets of Male Headers

1 review

Center female pin header for direct attaching the Raspberry Pi Pico. Extra USB connector for external power supply. Immersion Gold Process Black Base Panel, White Pinout Labels, Golden Rounded Outline, Stunning Aesthetic *Please make sure there are no pin conflicts between the modules you want to use together before connecting. Raspberry Pi Pico and...