Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: RBD-0704
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: RBD-1114
N20 Micro Gear 12V 100RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel
Reference: RBD-1214
The board is compatible with Mega 2560. excellent solution for developing projects based on ATmega2560. The board can be powered directly through the Micro USB connector The maximum output current upon 5V is around 800mA, while on the 3.3V it is about 800mA.
Reference: RBD-1249
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 90mA
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-1571
Length: 10″. Pitch: 4.5″. Weight: 25 gm. Shaft Diameter: 9.5 mm. Total Length: 10 inch / 250 mm. Material: ABS
Reference: RBD-1767
Neodymium Magnet Shape Ring Dimension 48 mm Dia x 4.5mm Thick 7mm Hole (3.5mm)
Reference: RBD-2135
433 Mhz Remote Control and Wireless Receiver Module Learning Code 1527 Decoding 4 Channel Output with Learning Button DIY kit for Arduino/ARM/MCU Suitable for wireless power switches, remote control sockets, LED lights, electric doors, and more.
Reference: RBD-2151
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
Reference: RBD-2194
Premium Quality Soldering Wire/Lead Low Melting Point Weight: 20-22 Gram 0.8mm Known as Lead or Solder Wire Melting Temperature 180°C Approx. (Tested by RoboticsBD LAB) We suggest this solder wire/lead paired with this solder to make your soldering work easier. Check GOOT Original KX-60R Soldering Iron 45W Check GOOT Original Soldering Iron TQ-77 here
Reference: RBD-0367
Brand: SparkFun Electronics
Reliable and powerful ranging and proximity sensor for drone, robot or unmanned vehicle applications Compact, lightweight with low power consumption User-configurable allows adjustment between accuracy, operating range and measurement time Communication via I2C and PWM Requires a power source and an external micro-controller running an application....
Reference: RBD-0493
Temperature Range : 0C-400C Shield Material : Metal Total Length(Approx.) : 2M / 6.6 Ft; Weight : 46g;
Reference: 0828
Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking. Choose your...
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-1543
Constant Current: 30A (Max 40A<10s). BEC: 5V 3A. Input Voltage: 11.1 ~ 11.7 V. Li-Po battery: 2S ~ 3S. Ni-MH 4-10 CELLS Auto Detect. Current stock is without connector
Reference: RBD-1572
Length: 11″ Pitch: 4.7″ Weight: 27 gm Shaft Diameter: 7.86 mm Total Length: 28 cm Includes a set of reducers (3,4,5,6 mm)
Reference: RBD-1716
Working Voltage: 5.0V Maximum Working Current: 100mA Data Interface Level: L<0.8V, H>2.7V, maximum voltage level 3.3V Particle Measurement Range: 0.3 ~ 1.0μm; 1.0 ~ 2.5μm; 2.5 ~ 10μm Note: Please purchase this adapter board to use it with Arduino and Raspberry Pi.
Reference: RBD-0660
Material: glass fiber Can connect 1-4 ESC. RoboticsBD This has an XT60 plug to connect a battery.
Reference: RBD-1603
USB-TTL converter. Logic Level: 5V. Operating Supply Voltage: 5V. Digital I/O Pins: 14. Analog I/O Pins: 6.
Reference: RBD-1691
Model: Emax SimonK Series. LiPo Battery Input: 2 ~ 3S. Continuous Current: 30A. Burst Current(10S): 40A (for 10Sec). BEC Mode: Linear. BEC Output: 1A/5V.
Reference: RBD-1701
Brand: SparkFun Electronics
Capacitance Meter DIY Kit Sparkfun Electronics
Reference: RBD-1719
Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December
Reference: RBD-1742
Holds 10 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 78X 60 X 28 Weight: 27.4 gm Material: Plastic Internal Connection: Series
Reference: RBD-0553
Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
Reference: RBD-0918
Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. RoboticsBD Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking.
Reference: RBD-1139
Type: Debugger/Programmer Tool/Board Application: Debugging/Programming MCU Supported Families: Flash-based PIC MCUs Core Architecture: PIC, dsPIC
Reference: RBD-2215
Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.
Reference: RBD-2289
Low cost, compact size dust sensor module Used to quantitative particle (> 1 micron) measurement Principle of particle counter Can sense the tobacco smoke and pollen, house dust Consist of light emitting diode lamp, detector, signal amplifier circuit and heater Used in applications such as the air cleaner or air purifier Users can use this sensor...
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-1399
Operating Voltage: 12V DC Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick...