How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-0732
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0989
Hold A standard 18650 batteries Wire : 15cm Output: 3.7v Dimension (Appro.): 76x20x20xmm Weight: 8gm High-quality plastic material
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0314
Colour: Red, Green, Yellow, White, and Black, etc. Cable length: 40 cm. RoboticsBD Net weight: 50 gm. They are very useful for connecting components to wires. It is insulation covered clips connected to the wire from both ends. RoboticsBD *You will receive 1 pcs cable of random color.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-1545
Input voltage 9~40V Output: 5V Maximum output current 2A Efficiency: 76-90% Material: electronic component
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-0350
100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-1673
Supports Qualcomm Quick Charge 3.0 fast charging protocol Has both "USB type C" and "Micro USB" port for charging power bank battery Power bank battery can be fast-charged (up to 15 watts) with QC 3.0 supported fast chargers Two "USB A" ports with maximum 18-watt power delivery from the power bank Power bank battery level indicator LEDs and power on/off...
Reference: RBD-0394
They are very useful for connecting components to wires. It is insulation covered clips connected to the wire from both ends. RoboticsBD
Reference: RBD-0402
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC
Reference: RBD-1705
3A DC-DC Buck Step-down Converter Constant Voltage 5V Fixed Output Module
Reference: RBD-0564
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-0422
Dimensions: 210 x 17 mm(LxW) Weight: 8 gm. Fit for Fingerprint Scanner - TTL (GT-511C3) & Fingerprint Scanner - 5V TTL (GT-511C1R) Wire Sleeve material: Silicon. RoboticsBD
Reference: RBD-1780
1. MINI USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 20 x 17.5 mm .
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-1855
Input voltage: 3-40V Output voltage: 1.5-35V(Adjustable) Output current: Rated current is 2A, maximum 3A Switching Frequency: 150KHz Operating temperature:Industrial grade (-40 to +85 ) Conversion efficiency: 92%(highest)
Reference: RBD-0990
Support any Chinese text, English text synthesis, and support for English mixed Support voice codec function, the user can use the chip for direct recording and playback Support speech recognition function, can support the recognition of 30 command words.
Reference: RBD-1098
Interface: I2C Operating Voltage: 3-5VDC Ports: 8-bit Parallel Ports Can be used with Arduino and Raspberry Pi
Reference: RBD-0763
Cell Quantity: 2 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-0764
Cell Quantity: 3 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-0765
Holds 4 AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 62 x 58 x 15 Weight: 15 gm Material: Plastic Internal Connection: Series
